kelsodeez
Active Member
im finally parting out my project that i never finished. i need money for my new project (the mini cooper) so my loss, your gain. i prefer local pick up, but i will ship at your expense. Buyer assumes all paypal fees. all parts are new, i just installed them and then took them off.
B16B w/ S80 transmission-$3800
i did a full leak down test on this engine and it passed with flying colors. brand new water pump and belt. factory N1 crank pulley, spoon valve cover, 5zigen oil filter relocator, drain back breather box for valve cover, the EK i took this engine out of had about 24,000 miles. does not come with distributor or intake but if you want the msd pro billet dizzy and the OBX itb's, we can work out a package deal.
the shell-$1500
perfect, straight body with brand new saab dolphin gray paint, roll cage, rear DA disc brake conversion, F&F type 1 coilovers, skunk2 front camber kit, all new suspension bushings everywhere. this shell is stitch welded and pop riveted everywhere. SUPER rigid chassis. comes with everything but what is listed for sale.
OBX individual throttle bodies w/ RC310 injectors- $575
i have gone through these itb's, taken down rough edges on the casting, replaced all the cheap hardware with nice stuff and modified the fuel rail so it will fit in a crx with a type r swap + DA brake booster.
Wilwood dynapro twin block calipers w/ steel braided lines and brand new hawk HPS pads - $450
Fastline shifter- $150
Fuel Safe 12gal- $550
15x7 ravs engineering (fake volks) with hankook ventus z214 c51-$1000
zero miles, already heat cycled by TireRack.com so they are good to go.
Mugen replica header-$150
OBD2 to OBD1 jumper harness-$35
Full Race traction bar and 1/2 radiator- $500
MSD pro billet distributor w/SE coil driver ignition-$475
Tunerview RD1 gauge display w/usb connector- $250
Hasport mounts EFB (hydro)- $350
Innovative cable to hydro conversion- $200
B16B w/ S80 transmission-$3800
i did a full leak down test on this engine and it passed with flying colors. brand new water pump and belt. factory N1 crank pulley, spoon valve cover, 5zigen oil filter relocator, drain back breather box for valve cover, the EK i took this engine out of had about 24,000 miles. does not come with distributor or intake but if you want the msd pro billet dizzy and the OBX itb's, we can work out a package deal.
the shell-$1500
perfect, straight body with brand new saab dolphin gray paint, roll cage, rear DA disc brake conversion, F&F type 1 coilovers, skunk2 front camber kit, all new suspension bushings everywhere. this shell is stitch welded and pop riveted everywhere. SUPER rigid chassis. comes with everything but what is listed for sale.
OBX individual throttle bodies w/ RC310 injectors- $575
i have gone through these itb's, taken down rough edges on the casting, replaced all the cheap hardware with nice stuff and modified the fuel rail so it will fit in a crx with a type r swap + DA brake booster.
Wilwood dynapro twin block calipers w/ steel braided lines and brand new hawk HPS pads - $450
Fastline shifter- $150
Fuel Safe 12gal- $550
15x7 ravs engineering (fake volks) with hankook ventus z214 c51-$1000
zero miles, already heat cycled by TireRack.com so they are good to go.
Mugen replica header-$150
OBD2 to OBD1 jumper harness-$35
Full Race traction bar and 1/2 radiator- $500
MSD pro billet distributor w/SE coil driver ignition-$475
Tunerview RD1 gauge display w/usb connector- $250
Hasport mounts EFB (hydro)- $350
Innovative cable to hydro conversion- $200
