Search results

  1. S

    Want to drop a 2.2 vtec lump into 4th gen accord

    I've been in this golf, it's an Audi 2.0 litre lump. The car was made in 1984! This guy wants to get rid of the VW because it's a fags car (Jesse from fast and furious) and he's bored of painting his fingernails black.
  2. S

    B16a2 in an EG hatch

    Hi All, transplanted a B16a2 OBD2 motor onto our EG hatch. Didn't want to change the harness, so we fitted a JDM P30 ecu (which plugged straight in) and wired up the engine. All appears to work fine, except the engine is running rich- does anyone know what may be causing this? We've also...
  3. S

    B20 Bottom End In A Jdm Sirii

    Hi all, We have a JDM SiR II 1993 EG hatch fitted with a B16a2 by Honda Japan. I'm thinking about changing the bottom end for that of a B20 and mating it to the B16a2's head. Does anyone know what will be needed to do this? Will the car's standard P30 ecu, driveshafts and tranny all be ok? Do...
  4. S

    Burning Oil When Vtec

    Sounds like it could be the lower rings of the pistons. Pistons have three rings, the first two are for compression, if these were faulty the comp test would have shown it. The bottom rings are used to sweep the oil off the cylinder walls, if these are bad then oil stays in the compression...
  5. S

    B16a Running Very Rich

    Just had an emmissions test done on our car. The garage said the engine is running very rich and the CO and hydro-carbon readings are off the scale :o The engine is OBD2 B16a2 being ran by a JDM P30 OBD1 ecu. All works fine (at least that what we thought!) Does anyone know what we can do to...
  6. S

    B16/b20 Hybrid

    Thanks all :)
  7. S

    B16/b20 Hybrid

    Hi All, We have a 93 Civic fitted with a B16a2 engine. We're looking into replacing the bottom end for that of a B20, and keeping the B16a head. Does anyone know what will be required for this hybrid? 1/ Will the B16a gearbox fit? 2/ Will we need hybrid engine mounts for the EG chassis? 3/ Will...
  8. S

    B16a2 Excessive Oil Consumption

    If it was something bad like a piston ring, wouldn't the engine make blue/black smoke? Would power remain the same?
  9. S

    B16a2 Excessive Oil Consumption

    Hi All, Our B16a2 has been using loads of oil recently (a litre for 500 miles!) There are no obvious leaks from the engine, and no blue or black smoke from the exhaust. The only symptom we noticed is that there was a ton of white smoke when we vtec'ed it hard yesterday. Someone suggested that...
  10. S

    B16a2 Axel Lenghts

    We got an obd2 B16a2 in our 93Civic hatch. Can anyone advise what length the axels should be for this swap? I was told Integra axels should be ok, but just need to know the length of them. Thanks
  11. S

    Oil Level Warning Light B16a

    Thanks! VTEC is working fine and the oil is at the correct level. I just wondered why the light wasn't coming on. I think we may not have connected this properly.
  12. S

    Oil Level Warning Light B16a

    After putting our B16a2 into a 1993 EG civic, I noticed that the red low oil warning light on the dash no longer works. Does anyone know where on the engine this sensor is meant to be? I think we may not have connected it. (The light used to come on with all the other warning lights when the...
  13. S

    Aircon In An Eg Swap

    Basically, I have noticed that there is a metal pipe from the air con which goes to the bulkhead of the car behind the intake manifold. On this pipe is a green plug which, on our car, isn't connected. Will try to post a photo if poss. Just want to know if any one else has this, or can tell me...
  14. S

    Aircon In An Eg Swap

    I'd be grateful if you could ask your friend Helmes :D
  15. S

    Aircon In An Eg Swap

    Just put a B16a into an EG Civic hatch. The car had air con originally and we want to keep it. I've changed the air con pump to one from a B16a, but does anyone know if there are any other parts which connect to the actual engine? Reason I ask is because on the bulkhead there seems to be a green...
  16. S

    B16a2 Axles

    Thanks Poot. I assume you should use the halfshaft from the 99Si as well? Do you know if axles from a JDM SiR EG civic will fit??
  17. S

    B16a2 Axles

    Just to clarify a point regarding Integra axles, can we use the axles from any model Integra, including Type R? What engines came in the 94+ Integras?
  18. S

    B16a2 Axles

    Should the axle be completely straight from the gearbox to the wheel, or can it be slightly bent?
  19. S

    What I Need For B162 Swap

    From what I've heard about Osaka, you'll get a better B16a from Afganistan!!
  20. S

    What I Need For B162 Swap

    That's Osama dude
  21. Try your Search on Google

Back
Top