Search results for query: *

i have a b18b turbo '91 crx that i converted over to obd 1. everything is just about done except for the hondata install. my tuner told me i could use a stock obd ls ecu to granny drive it (staying out of boost of course) to the shop but im having some problems getting it started. I think it...

i have a '92 hatch and i recently tried to install a radio when i must've mistakenly crossed a + and a - wire together. the raido blew and i have since taken it out. now i'm having some electrical problems. for example.. when the car is off the lights on my climate control stay on and so does...

FS: obd 0 b series distributor (new cap, rotor, and coil)....SOLD obd 0 PR4 ecu (manual) crx parts (post what you need) del sol dual core radiator (brand new in box) WTB: distributor plugs off engine wire harness for obd 1 distributor (i'm doing a obd 0 - obd 1 conversion) or complete obd...

email me w/ a price if you have either one. inspecta83@hotmail.com

quick question about the BOV that comes w/ the max rev kits....are they any good? and how do they compare to the BOV from the 1st gen dsm? better, worse, etc? thanks

just read something about making your own octane booster. octane boost and here (to the bottom in yellow) octane boost 2 just wanted to know what you guys thought...and also is there a such thing as running too high an octane? b/c i always thought the higher the better. if not, what's the...

i have a b18b1 t3/t4...the downpipe and exhaust pipe (no cat) is 2.5 inches and i got a ractive muffler ....pic.....now im having second thoughts...just wanted some imput as to if this is an ok muffler or whatever. thanks.

i have a obd 0 B series dizzy...totally rebuilt like new...$100 obd 0 PR4... $40 crx sunroof assembly....$50 92-95 civc seats (front and rear).....$50 del sol radiator/brand new in box (dual core).........$60 WTB 1994-95 LS dizzy and any of the following ecu's P74,P75,P06,PR4,P28,P30,P72,P61...

ok..i have a b18b with a hondata 2B and i just wanted to know which ecu should i get? i'm assuming that i'd have to get an obd 1 LS ecu (P75, P74, or the PR4). also, whats the diff between the 2B and the s200? thanks

im putting a max rev kit on a b18b and the intake side of the turbo is touching the block...so much so that i cant even get an air filter to fit on it. i am going to try to flip the turbo around so that the intake side is on the opposite side but, if this doesnt work, it looks like my last...

i am using a obd 0 crx engine harness on my LS engine and need to buy a 3 bar map sensor. i heard a rumor that the new model numbered GM 3 bar map sensor (12223861) is a little more difficult to wire up than the old one was. is there any truth to this and if so, what? also, would i have to buy...

quick question...i have a '90 dx crx that i need to replace the gauge cluster on. i found an Si gauge cluster and was wondering what i'd have to do to the dx wiring to make the si cluster work in my dx? is it as simple as just replacing the dash harness? thanks...also, if anyone has a dx...

ok, here's my setup.... '91 b18b crx, hondata2b, wolbro 255lph fuel pump, and i'll be boosting 10psi (and i kept the crx wiring so its still obd 0 with the resistor box)... i spoke to the peeps at rc engineering and they said that with my set up i would need 370cc peak and hold injectors. does...

ok, here goes...i have a '95 integra ls motor (odb 1) in my crx that i converted back to obd 0 using the crx engine harness. i thought that the motor was overheating b/c the coolant starts bubbling over into the reserve bottle on the side of the radiator after a few minutes and the climate...

i put a b18b into my '91 crx and it keeps over heating and i have no idea why. i did everything i could thing of....bypassed the heating core, checked the radiator, new water pump, new thermo and i even took out the thermo and after all this it still overheats. someone told me that maybe the...

i have a 95 ex coupe and i wanted to give it a lil more pep so i figured why not get a chip....just wanted to know which one would give me the most bang for my buck? (i.e. jun, skunk2, mugen, etc)

i know this is a dumb question but....im trying to tighten the castle nuts that hold the ball joints in, and everytime i try to tighten it, the whole dam thing spins, getting me no where fast. someone please tell me how to do this...thanks alot.

im wrapping up my b18b1 swap into a crx. i tried to hook up the speedometer cable today, but it seems to be too short. i am using the crx speedometer cable and was wondering....is the speedometer cable from the integra longer, and would it reach? or are they all the same size and i am just not...

im trying to wire up my b18b1 with a obd 0 crx dx engine harness....i already got it wired up for multi port injection (4 injectors) and now im just trying to plug it up to the motor. i altered one of the plugs on the engine harness so that it could fit the oil pressure switch. i just wanted to...

just needed some input for my soon to be boosted b18b1. in addition to doing cams, valves, retainers, springs, pistons and rods i was also planning on either re-sleeving or puttin in a block guard but i dont know which one would be better so i wanted to know the pro's and cons of each one. i was...