Search results

  1. C

    Another strut/shock question

    What is prostreet's website address?
  2. C

    ZC Swap Problems

    Is this going into a 90-91 CRX? If so then I think you need the ZC that came from the JDM CRX si (there are a few different ZC engines, integra one, brown top, etc...) so are you positive that you have the correct one? I have never done the swap though, those questions just came to mind. EDIT...
  3. C

    2000 GSXR 600 (Motorcycle) near Greenville, TX

    Here is a link to my Yahoo Classified ad: 2000 GSX-R 600 Reply with any questions, or e-mail me at jchookas@argontech.net
  4. C

    Another strut/shock question

    http://www.shox.com has them for $299 and $389 for springs too. There prices were the cheapest I had found for Illumina shocks/springs on a CRX and I think their other prices are pretty good. Good luck.
  5. C

    00 Si rims

    You can go to www.wheelweights.net for wheel weight/size info or go to the Articles section of the forums and find a huge listing of wheel weights and sizes. Hope that helps some. EDIT: Here is a direct link to the table of wheels: https://hondaswap.com/forums/index.php?showtopic=29358 I...
  6. C

    Rotated my tires, now the car shakes....

    Nope, they are very very cheap tires. Just some basic general touring high mileage ones.
  7. C

    Rotated my tires, now the car shakes....

    Well I went to Discount Tire Co. and told them to balance them. When they did, they found the front left tire had a small amount of tread seperation so they replaced it for "free" (it was actually 8 bux, but an 8 dollar tire is always nice :)). They balanced them all and now it's riding as...
  8. C

    do you like this?

    k thanks, I thought they looked a little big but didn't know.
  9. C

    do you like this?

    What size are those rims? 15's?
  10. C

    Tire Iron with poly protection for rims

    umm I think you guys are refering to the tool used to remove wheels from cars, reckedracing is talking about a tool used to remove/install tires onto wheels :)
  11. C

    Rotated my tires, now the car shakes....

    I put front to the rears, then the rears to front but swapped so: Front left -> Rear Left Rear Left -> Front Right Front Right -> Rear Right Rear Right -> Front Left I'm pretty sure that's right. I checked on the net and the site I found said that's the best way to move 'em for non direction...
  12. C

    Rotated my tires, now the car shakes....

    I just finished rotating all 4 wheels/tires and I went and drove it around and now the front end shakes a little bit (causes the steering wheel to shake and it gets annoying). It mainly is at 50-60 mph and when I am accelerating or decellerating at those speeds. As soon as I drop below 50mph...
  13. C

    Steering wheels

    What about pre 92 civics? I would guess that 4th gen civics and 89-91 crx are interchangable, but dont know for sure.
  14. C

    I got bad news today

    Same thing with my mother luckily. (it was benign, aka not bad kind of tumor ;)) Good luck JD, hope everything works out.
  15. C

    Specs for a SOHC ZC

    I think the SOHC ZC is from an 89-91 CRX Si, but I'm not positive on that. I bet the distributor is the problem but before you go out and get another distrib, you might wanna wait till someone else w/ more knowledge and tells you what they think.
  16. C

    The New CRX

    Did no one else notice this article is from early 2002???
  17. C

    Quick wheel offset questions

    oh ok, well the reason I asked is because of the other thread about falken azenis rubbing while turning. I believe you mentioned that 42mm was the right offset so that it won't rub. If its a 7" wide wheel what do you think it should be offset? Thanks to everyone for your help, I wanna make...
  18. C

    Quick wheel offset questions

    Awesome thanks guys, so I shoudl be able to run 42mm offest w/no problems if I use a 2 mm spacer w/ the 40mm offset? Also, is there any disadvantage to using a spacer?
  19. C

    Quick wheel offset questions

    If I have a wheel with a 40 mm offset, and I need 42 mm offset can I use a 2mm spacer to make it work? or would this make the offset 38mm instead of 42mm? Offsets always confuse me :hmm:
  20. C

    FYI: Tire Rub-O-Rama

    The wheels I want to get are 15x7 w/ 40mm offset, so this will rub if I run Azenis right? :(
  21. Try your Search on Google

Back
Top