Search results

  1. 2

    2 d16Z6 motors for sale

    what state are you in.
  2. 2

    Vtec problems. (I never kicks in)

    Have you checked the lost motion assembly if those are not moving freely, vtec will not work properly. Have you cleaned the selenoid. You know simply checking if the selenoid is clicking on and off is not enough, you need to see if power is getting to it when at operating temprature. Use a power...
  3. 2

    ZC high compression pistons/conn rods

    Bump! Someone got to want these pistons, great power potential
  4. 2

    FS: Parts > GSR, D-series,

    what specific engine are those vtec selenoids from. the z6 and the y8 selenoids are different and are they in good working order.
  5. 2

    d16z6 head &d16y8 block

    did you try using one of the y8 bolts. Thats what I did when I swithched heads and it worked. Its a good idea to use thread locker. Anyway I gained absolutely nothing from doing that conversion the heads are pretty much the same except for the combustion chamber and that gains you very little...
  6. 2

    ZC high compression pistons/conn rods

    I have a set of ZC high compression pistons that I pulled from my z6 block. They are in good condition I bought the pistons new and put my rods in them. These are 75mm pistons that fit in most d16 and d15 engines and can get you much higher compression ratio than stock depending on your...
  7. 2

    d16z6 head &d16y8 block

    Your distributor must be modified or something because I have done that swap before and the distributor from the y8 pluged right into my harness. I had a 94 Dx with the harness modified for vtec I dropped in a y8 in it everything plugged right in. As for you ecu question, I've never heard about...
  8. 2

    Friend needs help!!! with b18c1 in 95 civic

    it could be the cruise control servo. Pics might help.
  9. 2

    d16z6 head &d16y8 block

    What? If you are asking if your y8 distridutor will work with the z6 head, the answer is yes and no. It will plug into the whole and even run the engine but the mounting point are different so you need to either modify th mounts or just use the one from the z6. Hope that helps Someone correct...
  10. 2

    d series motor into a 93 Del sol

    Also you need to use the distributor from your del sol. The 99 mounts for the dizzy are different.
  11. 2

    F/S or trade ZC pistons and rods

    I definetly want to do this ASAP so that I can finish my build. what do you have from your turbo that you wanna trade. The only thing I really need for the turbo is the oil lines. Let me know what you wanna do
  12. 2

    F/S or trade ZC pistons and rods

    do you live in phoenix because if thats the case, u can come check them out
  13. 2

    F/S or trade ZC pistons and rods

    I have a set of ZC high compression pistons that I pulled from my z6 block. They are in good condition I bought the pistons new and put my rods in them. These are 75mm pistons that fit in most d16 and d15 engines and can get you much higher compression ratio than stock depending on your...
  14. 2

    Rod bearing caps

    when you tap the bearing cap assembly, tap it back and forth from side to side until it loosens up then wiggle it out. You are probably not using enough force since you are using a rubber malet the risk of breaking the caps are reduced so tap it a little harder.
  15. 2

    camshaft question

    thank you, I knew it was BS. I'm just happy they are sending me another one I just hope that lightning doesnt strike twice.
  16. 2

    D16Z6 opinions

    Why dont you do that right from the start anyways. I think you need to heed their warning before you end up spending like 2k on a motor that just refuses to run right. I have been down that road and guess what, at the end of this road, there is a turbo waiting for me. I just wish I had listened...
  17. 2

    D-series manual motor to auto tranny???

    also, the driver side engine mount is different at least in the 92-95. since the engine is from a manual, you will need to use the mount of that engine.
  18. 2

    camshaft question

    So I bought a zex/comp cams and installed it in my z6. The car ran for about 50 miles then I changed the head( ported polished, valve job). After everything was done, I went to turn the engine over and I heard a loud crackling sound and sure enough the engine wont start. I looked at everything...
  19. 2

    I need Advice......

    If your'e looking to beat the new gto which if I'm not mistaking makes 400hp and in order to beat that, you are going to need a turbo and if NA, you are going to need extensive engine work. If your'e on a budget I would go d16y8 with head work and turbo that mofo, tune it right and you might...
  20. 2

    ahhhhh no vtec...

    yea your lost motion assembly will do that I had it happen to me before but sorry i dont have a part number. btw you should check your manual because, I'm pretty sure your engine dont need 4.2 quarts unless there is something you aint telling us.
  21. Try your Search on Google

Back
Top