Search results for query: *

i really want $420 shipped...so that means 50 is for shipping so i guess $370 if you want to pick it up.

the whole exhaust system is kteller.

96-00 Kteller stainless steel exhaust!! 3" with 3" test pipe and downpipe flange. I Bought it all for $551 and selling it for $420 shipped plus 3%paypal fee!! Never been used, just sprayed the welds with high temp silver paint. test pipe the magnaflow muffler the gasket and flanges showing it...

it was a tight fit for my jdm b18c, but it does work.

i do have an SI header and yes i do have an o2 sensor before the doughnut gasket. THe problem is i have an o2 sensor at the cat too. OBD2!!

i have the 99-00 si manifold right now. only problem i have is my shiftlinkage is rubbing on my o2 sensor at the cat. any ideas on what to do?? btw B18C.

Which exhaust manifold will fit my cat?? i have a 2000 ex with a jdm engine and jdm exhaust manifold. I dont really want to use the jdm manifold because it wont fit so which other manifold can i use that will fit my 2000 ex cat???

yep, i got the hose already, engine is in the car. use gsr for upper and lower. works perfectly, just make sure to clamp it.

just use the 98 harness and then use the clips that are not on the 98 harness from the b16 harness. I did a obd2a into my 2000 ex and we used my obd2b harness and just use a conversion harness from obd2b to obd2a. works perfectly.

alright guys, gsr hose for both bottom and top. works fine with clamps.

NOT WORKING YET!!! I have two wires, RED and BLACK. the black was first hooked to ground and red to A26. That didnt work so i swap black to 12V, still didnt work. So i swap wires, black to a26 and red to ground, didnt work. Black to a26 and red to 12v still dont work. I am lost!!!:(

yea that is for obd1 ecu. i am looking for obd2a. i read some info that red wire goes to a26 and then the other one to ground..but it does not seem to work. just looking to see what other people use.

Black wire goes to ground and red wire goes to A26 on the obd2a ecu? I got so many different opinions. And how can you tell if the iab valve is working??? This is all on a JDM P72 Obd2a.

i am using my 2000 ex harness on my jdm 96 b18c, everything is connected except for one little clip thing next to the disturbitor. it has a blue and black stripe and a black wire. what is this?? i looked all over the helms manual for my civic but cannot locate anything at all. please help!

I tried searching but have yet to find a definate answer. I have a 2000 civic and i am swaping in a B18c, which radiator hose would i use?? i am keeping the 2000 civic ex stock radiator. So what hose would i need for the top and which for the bottom radiator??

sorry guys, i'm about to do a swap next week and i just want to make sure i have everything set straight. i just read about the crank angle sensor and i am a little confuse. I have a 2000 ex(obd2b) and i am swapping in a 97 b18c (obd2a) and i got the conversion harness, do i still have to wire...

some people suggest using 99-00 SI power steering pump, why is that?? cant i just use the GSR pump??

yea i just found them! i asked before i tried. but i am still stomped on a definate answer on the power steering. just use SI pump and all my d-series belts??

Alright i'm about to order my swap from hmotorsonline but i need to figure out how to keep my power steering and how to keep cruise before i jump into this!! someone please help, i tried searching but no one has a definite answer. please help!!

alright guys i am about to swap a b18c into my car. before you guys swap, what do you guys do?? change water pump?? change timing belt?? or just put it in and run her??