Search results

  1. P

    b18c4 specs

    I clearly remember reading somewhere that the C4 was rated at 180-hp similiar to the JDM spec Integra SiR-G B18C.
  2. P

    D15B2 vs. D15B1

    I've only heard the d16z6 head on top of the d15b pm3 block with vtec ecu makes more hp & torque than the stock d16z6. I did that swap, however, the high compression ratio blew my brandless head gasket within 3-4 months. I should have gone with the genuine Honda head gasket during that time...
  3. P

    SiR cluster fuel light ?

    The low fuel lights light up via the low fuel sensor. The floater is resistance based and only works to move the fuel gauge needle. I believe your Civic is already wired up for low fuel sensor but your sender lack the low fuel sensor unit. (see pic of sensor, located just next to the floater)
  4. P

    Re-wire fuel injectors

    No sequence for the yellow/black wires. If they were, Honda would color them differently.
  5. P

    Resistor boxes

    Resistor boxes - all the same. Bogging problem - too many causes. Any check engine light? If no, change fuel filter, flush injectors etc.
  6. P

    D16Y8 in eg hatch??

    VX engine harness - YES with Z6 ecu & fuel injectors. Change the plugs on the Y8 dizzy to the Z6 ones. Or change the Z6 engine harness dis plugs to the Y8 ones. Y8 engine harness - YES with Y8 ecu. OBD1 to OBD2 ecu convert harness req'd That's all i can think of.
  7. P

    ignition coil in h22

    You have a JDM H22A distributor? Anyway, sounds like an ignition module problem. Its located inside the distributor. Replace it and it will be fine.
  8. P

    Car starts then cuts off then starts but smokes crazy after IM,TB,Hond

    I had this experience before. Turned out to be a leaky brandless head gasket. I kept losing a substantial amount coolant with increasing progression after each driving month to the point I needed to top up with each trip. At some starts, I thought the starter jammed but turned out actually there...
  9. P

    b20a2 swap

    Regardless of chassis. Your project will be possible if it was a B20 CRV block.
  10. P

    Battery Dies Every Day

    Had that experience once. Found out that one or a few rectifier diodes in the alternator were shorted, thereby drawing power from the battery. When this happens it only takes less than half a day to drain out the batt. One simple check is when the engine is cold, the alternator should feel warm...
  11. P

    need help 2 identify my new intake manifold

    That's a H22A 92-96 Prelude intake manifold. How was that being able to fit on a B-series head? There weren't supposed to be holes at the runners or EGR chamber, probably drilled then re-filled. Anyway its free.
  12. P

    D15B 3 stage

    Will work but may not run well. You can try activating between the 2nd and 3rd stage. Leave the 12-valve 1st stage out, which means powering 12V to the spool valve with the red wire(?) all the time. You will also need to add a vtec oil pressure switch to the spool valve with the green/yellow...
  13. P

    B16A1 in EF won't start.

    Did I read wrongly? You actually ran your motor without coolant??? You didn't know how fast the engine would fry without coolant? The least you could have is water inside.
  14. P

    Type R Cams, Valve and Valvetrain Motor Swap Upgrade

    I've a neighbour who has an Integra GSR B18C who performed the swap. He found the part numbers for GSR intake dual valve springs P72 to be the same on the Type R exhaust side, same can be said for the 32 retainers P30 & seats PR3. I understand that if you buy aftermarket camshafts [ie. Toda...
  15. P

    Type R Cams, Valve and Valvetrain Motor Swap Upgrade

    I have a 170ps stock jdm B16A lying around unused for 4 years and a used jdm ITR manifold and header. I am looking to upgrade the camshaft, valvetrain internals. After looking through the list of parts. I am looking to get the CTR intake and ITR exhaust camshafts along with other valvetrain...
  16. P

    EK4 SIR QUESTION

    An OBD2 B16A manual transmission ecu from the same market where this EK4 came from is highly recommended to save on getting a conversion harness or conversion, as well as avoiding CELs for missing VTEC oil pressure switch and crankshaft position sensor. EK4 SiR B16A engines from singapore are...
  17. P

    Why you dont put remote start on MTs

    These remote starting devices must be properly installed and certified, as it can miam or kill someone. Luckily the wall and gate isn't somebody's legs, child or pet.
  18. P

    Exedy Thin Cerametallic Clutch Problem

    Is the clutch pressure soft when cold and hard when warmed up? Could be a worn out clutch hose, linking to slave cylinder hardline.
  19. P

    Some Turd Ball Car My Brother Has to Clean

    What can I say, its a 007 car. Does the hood come with a dual turret option?
  20. P

    ECU question

    Am running the D15B VTEC + P28 manual transm. Able to get 240 miles on one full tank in full city driving + occasional hard driving too. Haven't tried with P08 though.
  21. Try your Search on Google

Back
Top