Search results

  1. lickety_slickjj

    eg b18c swap pics...finally

    lookin tight!!!!:drinks_drunk:
  2. lickety_slickjj

    92-95 d16z6 into 00 hx

    i do have the manual tranny mounts, i haven't even thought about the motor mount positions though??? both singles- both coupes, i don't think the motor mounts changed from 92-2000??? thank you for the input... i am doing this swap next weekend, hopefully it is only going to take one full good...
  3. lickety_slickjj

    92-95 d16z6 into 00 hx

    i am a pretty damn good mechanic, especially with my imports, but i just like to be prepared for everything if i can be....:driver: so any imput would be appreciated from someone that has done an auto to manual swap in a 99-00 civic or obd2b to obd1 swap.
  4. lickety_slickjj

    92-95 d16z6 into 00 hx

    so i have a 00 hx obd2b, auto, i am swapping it to a d16z6 manual. i have the motor, tranny, linkage, p28 ecu, obd2 to obd1 jumper, whole pedal assembly, well everything. i am just wanting to make sure about the wiring. i am still a little worried about the engine wiring. is there anything that...
  5. lickety_slickjj

    d16z6 into 00 civic hx

    can i use the z6 obd1 engine, head, and im with my hx obd2 harness, obd2 ex ecu, and my hx distributor? will that work or cause a bunch of crap or can i use just the obd1 z6 vtec head with my y5 im and my hx distributor,and the obd2 ecu? would that be better? i just was thinking of putting a...
  6. lickety_slickjj

    bearing issue?

    sorry, i went within specs with new king and acl standard bearings,and i used a y8 oil pan ,y8 oil pump,and ay8 pick up.
  7. lickety_slickjj

    bearing issue?

    ok so i put a mechanical gauge in and it reads about the same, how do i check the pump to see if it is bad?also i think my seals in my turbo may be bad cause there is a little oil in the intercooler pipes,but not much and it doesnt smoke. but i drove about 45 minutes away and i checked the oil...
  8. lickety_slickjj

    bearing issue?

    thank you for your help. i did check the bearing clearance with plastigauge and you measure how wide it is after it is smashed almost down to nothing. well i am going to check it with a gauge tomorrow. thanks again.
  9. lickety_slickjj

    bearing issue?

    d16z6 t3/t4 turbo with 8 psi, i just installed an aftermarket oil pressure gauge, when i first start my car when it is cold, my oil pressure goes up to like 75 psi, after about 5 -10 minutes of driving my car the oil pressure drops to zero at an idle. i have the feed line ran off the back where...
  10. lickety_slickjj

    no codes, no vtec?

    anyone? there are no codes. any ideas of what to check????
  11. lickety_slickjj

    no codes, no vtec?

    i have a d16z6 with a t3/t4 turbo,chipped p28 with uberdata,my alternator went out, i replaced it and a brand new battery. i reset my ecu,cause when the alternator went out, my vtec stopped kicking in? i have checked the wiring, the oil, and have tapped the vtec wire on the positive terminal...
  12. lickety_slickjj

    will 96 hb kyb agx shocks fit on my 92 civic, help me ASAP before they go?

    i believe the shocks and springs are the same from 88- 2000. so yes i am almost positive they will fit. i just swapped suspension from a 88 civic to my 92 civic and vise versa. worked out mint.
  13. lickety_slickjj

    no boost in first?

    sorry, just wanted to add that i also have oil all over in my intercooler piping!!!!!!!
  14. lickety_slickjj

    no boost in first?

    first of all, thank you for the info. and the turbo was on the car when i traded my screwed up hatch for it. and i am looking to get a new turbo, (a smaller one), because it doesn't do much for me unless i am on the highway and hallin ass. so if i get a different turbo, would i have to get a...
  15. lickety_slickjj

    D series Civic parts

    how much for the rocker arm assembly 98550?
  16. lickety_slickjj

    no boost in first?

    i can't get boost in first gear, it is a t/4 xs power turbo on a d16z6? any ideas?
  17. lickety_slickjj

    help!!

    i am running 8 psi. i am routing my feed line the right way this weekend, and my vtec does kick in at 5000 rpms everytime. i read that the p28 chipped with uberdata doesn't read the vtec oil pressure switch? and i don't have the vtec pressure switch. my check engine light does not come on every...
  18. lickety_slickjj

    wastegate

    what is the hole on the top of an external tial wastegate for? someone said it was for the wastegate adjustment, but i don't know. and there is nothing in its place. i know this is a stupid question, but i am just learning about turbos. thank you.
  19. lickety_slickjj

    help!!

    still no code. and it doesnt just come on at higher rpms, sometimes it comes on once i start slowing down or after i slow down. and what is egt, sorry i am just learning about turbos along with a lot of other stuff.
  20. Try your Search on Google

Back
Top