Search results

  1. S

    Mini Me Problem

    just a guess but when i put the Y8 on my Z6 head the hole for the Y8 coolant line on the intake mani is round(and the Y8 head is round too) and the Z6/A6 is rectangular, did you modify the gasket for it? cuz if not that is more than likely your problem
  2. S

    B17a Cylinder Head Totally Complete

    This head is from a 92 Integra GSR w/180k miles on it that i picked up wrecked for the transmission for my cousins LS swap in his CRX. The car blew no smoke and the head is in excellent shape. It comes totally complete with: -Cylinder head, valves,springs,retainers,camshafts,cam gears,cam seal...
  3. S

    Vtec Stuff

    https://hondaswap.com/forums/index.php?...E=02&f=2&t=6681 check here for the instructions and this diagram above, i wasn't trying to be smart either, just trying to help out, but really if you are going to spend the 75 bucks for the controller, you might as well get the PR3 ecu, adding the RPM...
  4. S

    Vtec Stuff

    are you not using the PR3 or PWO ecu designed for your motor? or are you just trying to hook up a vtec controller type deal? if so get a decent vtec controller for cheap(fields) or just get the MSD rpm switch and rpm activator from summit racing, its like 75 bucks for both of them.
  5. S

    Ls Rods

    the advantage to the LS rods is strength due to its larger width in comparison to the dseries rods(most sohcs). The pistons(toyota pistons) should yield in a Z6 engine(sohc vtec) 9.2:1(don't quote me on that but it will be low) and the toyota pistons will just be easier than modifying the LS rod...
  6. S

    Best Motor For All-motor Crx

    i never said DOHC SUCKS in my profile did I? BTW the website is mine and i love the DOHC's, well most of them, as well as the SOHC's, i just happen to love dispelling the myth that the SOHC can't be made to make power, that it sucks, and it will take a whole lot more money to make it as good as...
  7. S

    Best Motor For All-motor Crx

    sure......if the vtec turbo is using the VX motor, do some more research and try again btw i hope your quote was just sarcasm
  8. S

    Ls Rods

    YES IT WILL WORK: Small End - I had found specs on the internet somewhere, and you can give that to the machine shop, but I bet you can give the machine shop the wrist pin and they can rebush the small end (they should have bushings there). Big End - The on the big end diameter on the LS rod...
  9. S

    Need List Of Parts To Do A Mini Me

    i second that the ZC block will not bolt to the Sohc head, unless you are referring to the D15B JDM sohc vtec motor that is labeled ZC, the DOHC block will not bolt up to the SOHC without machine work, and money, but it isn't worth the money, so why are we talking about this?
  10. S

    Pr3 Question

    get a fields controller and you can bump it up to 135, but you are going to kill yourself or someone else going that fast so don't do it, and yes i am your father.
  11. S

    D16z6

    ok heres a real response to what you asked instead of people making fun of your inexperience: 1. 8 PSI bolted on turbo kit,stock bottom end, i would do the intercooler though its worth it and its safer 2. 10-12PSI(pushing it on 12 but its been done), only if you are going to keep the bottom...
  12. S

    What Turbo To Get?

    I didn't want to bring this post back to life but i had to because it kinda brought to my mind some ideas that people were forgetting: 1. 75 per cent of the fastest running(1/4 mile) cars are VTEC powered, that has to account for something cuz these people wouldn't put lots of money into a...
  13. S

    Any Wiring Guru's? Make $200+...

    oh i just read where you are at, well email me and i can help
  14. S

    Any Wiring Guru's? Make $200+...

    i've done the exact swap except with an 89 dx swapped over to the MPFI Si harness and resistor box with a 92 XSI grey plug motor, where are you at? i'm in charlotte, nc
  15. S

    1st Gen B16a Oil Filter

    what he said, plus almost every civic/integra/crv/del sol/accord from 89-00 use the same oil filter.
  16. S

    Crankshaft Pully

    you can use any 92-95 sohc alternator if you can get your hands on one, i think the 96up sohc will work too, but don't quote me on that one.
  17. S

    Will Obdii Dist. Work?

    i would have to say it would only work correctly if you have the OBD0-OBD1 harness and then direct wire it, thats the setup in a 92-95 hatch we have with the b18c obd1 ecu and obd2 dizzy and it works just fine.
  18. S

    Need My Ecu Rechipped.

    get a stock ecu that is for your car or get hyperducktuning.com to reprogram it to stock, buy a 5 wire O2, get afc and the fmu and go to a dyno, i wouldn't trust a photocopied ecu for a turbo application.
  19. S

    Crankshaft Pully

    will the dx alternator plug work with the Z6 alternator, it does on my 89 SI and plugs right in, if the plug is the same use a Z6 alternator and the Z6 crank pulley, each pulley is designed for each motor, as much as people would like to disagree i have a bad oil pump i will sell to some one...
  20. S

    B16 Inot A Crx Without Mount Kit..

    1.use the 90-91 Acura integra 5spd motor mounts get the L bracket for the rear mount too. 2.Move the rear mount to the hole next to the hole its in on the rear cross member(threaded bolt hole) and you'll have hammer down part of the lip of the frame rail so the L bracket will work(look on...
  21. Try your Search on Google

Back
Top