Search results for query: *

5 years ago I had U-Haul install one of their hitches on my 90Si with ZC. I towed a 4x8 enclosed trailer from Denver to Dallas. I figured it was roughly 2000# total (trailer/junk). With the ZC I have the close ratio gearbox and tall final drive so I had to dump the clutch at 4k to get...

I'm looking for the rear hatch area cover (can be "split" at hinge... doing a custom speaker install ;) and the belt tensioner for the a/c setup. Got either? Jim Dallas/DENVER

Looking for a factory trunk cover for a '90 Civic hatchback. Split at the "joint" is ok, I need something to butcher to fit speakers then I'll recover it. Cheeeeeep is good ;) TIA Jim Dallas

what's a decent vendor to deal with on the Magnaflow? I did buy a DC cat back system for the car in 2001 when I was prepping for the swap. The "less than helpful people" I bought it from in Arizona shipped me the CRX version. Idiots. They wouldn't ship me the correct one unless I prepaid...

don't ya hate when you hit return by accident? Anyway, the Walker was a step down from stock (yes, I had the original 1990 factory system still on the car), considering that the muffler had just started to rot through. I'll keep what I got until a deal pops up on a Magnaflow setup...

Yeah, that's what I suspected. The Walker was

Hi, While surfing eBay for bits and pieces I found this setup: eBay Motors: HIGH FLOW CAT+HEADER+EXHAUST 88-91 HONDA CIVIC/CRX 90 (item 290062167218 end time Dec-20-06 18:03:23 PST) If the link doesn't work, it's ebay item 290062167218 Anyone bought from these guys? Is the system any...

All fuel injected? Jim

Does anyone know what other models/years used the same relay? As in, exactly the same? Something I don't have to rewire/wire around/replace connectors to make work? The one in my '90 Si is starting to be intermittent.. sometimes a gently tap (small hammer) is enough to get it to kick on...

I had a similar problem with 1990 Si/ZC setup. Turns out the temp sensor lead was making intermittent contact. The difference with mine is that it'd sometimes do 2500/3500/2500/3500/2500/3500............ sometimes it would do 1000/1200/1000/1200.... Splicing in a "new" connector to the...

How about a few specific details? What year/model chassis, which ECU are you running and what are the actual ECU codes it's kicking back? I'm think I'm finally at the end of debugging my ZC conversion, 1989 JDM Civic ZC into a 1990 Civic Si with '89 teg ECU. It's been a 5 year process that...

North Texas. The only problem with changing shops is the $39.50 fee each one charges for the inspection. I get one free retest at the first set of yahoos then it's open. New cat is on the way, I'll put that on, tweak the timing and keep my fingers closed. My '89 Teg used to pass...

Yeah... I only went to this place because it was close to work so I could do it over lunch time. There's a chain of Kwik Kar places in Texas... there's another shop that's "Honda friendly", but 3 towns away.

I'll do what I can about the warm up... it's a private service station so I takes my chances on when they'll get to me. Today there was no one in line so it was actually pretty quick. And I suppose 200k miles is too many for the factory cat? Especially since I finally cleared up the temp...

Just got back from my local emissions test. HC was ok, CO waaay low... but I got killed on the NOx reading. No, not nitrous oxide. ;) Any good suggestions for things to look for, check etc? The car: 1990 Honda Civic Si The engine: 1989 JDM Civic ZC The ECU: 1989 Integra 5 speed I don't...

Ok, picked up the drivers side axle... wrestled it in and so far so good. I owe jlicrx a definite beer or 3... :D When I researched the swap in 2000 it was straight forward.. use '90 Teg axles. Somewhere along the way someone insisted it was 2 passenger side... and I guess I'm a dumb *ss for...

So do I use the drivers side for both axles? Or use a "set" ie drivers and passenger for replacing what I got? TIA Jim

I need a new axle for the drivers side on my '90 Si with '89 ZC. The 1990 Integra 5 speed axle would be perfect.... except on the trans end the splines are only cut for 1/2 the distance on the stub. I tried to fit one of those.. no go. I need an axle splined the complete way. Is there a...

I'm interested in the head/valve cover.. although I really only need the valve cover. The one on my '89 JDM Civic ZC was cracked in shipping to the US. :( anyone else need just the bare used head? Jim

thx, I'll check that tonight. I'll also do the resistance check on the sensor. Jim