Search results for query: *

doesnt make sense why you wouldnt keep it. its your evap system

well where should I run the vacuum line coming the drivers side of the intake manifold because usually it runs to the purge cut solenoid then to the evap cannister

timing is bang on. I was looking at the map sensor and vacuum lines. and I am using the old stock 88 civic map sensor with a vacuum line siliconed to the hole for the MAP in the d16z6 intake. I went to the wrecker and got a d16z6 MAP sensor so I am putting the proper one on right now! what I...

so for a second time I checked for vaccuum leaks and found a crack in the hose going to the fuel pressure regulator. so I replaced the hose and it is running alot better but I still get the odd misfire!

yes I have also done that

I have a 1988 civic lx with a d16z6 obd1 swap. and I have a misfire that I cannot get rid of. heres what I have ruled out so far! - done a compression test (150 psi across all cylinders) - within range - changed plug wires - no difference - checked for vaccumm leaks - none found 2morrow I am...

lol some people are funny... the headgasket would be the last thing I would suspect. its 3 dollars for a little bottle of engine oil and dye and u can find a highwattage black light bulb and put it in an old school trouble light that takes bulbs. 10-15$ cost to diag, assuming you have a older...

s'all good

lol what u mean something tells u no. I looked at my exhaust and I have one. I did a compression test. number one cylinder loss of compression. I burnt one of the valves im guessing. what im hearing out the exhaust is the valve not sealing properly, therefore it has to be an exhaust valve or...

damn I wish you asked bout that bolt earlier today, I just adjusted my valves today.

thats fuked!! fuk the lawsuit. Id just crash a plane into their building if I was you! I wonder what other corners they cut! what kinda warranty did u get with the rebuild?

its not a resonating popping noise. I have a resonator. its not a loud popping noise. its just a quiet pop pop, and the motor sounds like it is running shitty. almost like a sticky exhaust valve, slight misfire, or something.

okay well im thinking my bogging was from possible low fuel going up a hill. so I fueled it up and havent had it bogg yet. as for the popping noise this is still heard from the exhaust pipe. im going to adjust the valves tommorow. if the valves do need adjustment do you think this would cure my...

I have a 88 lx civic with a d16z6 obd1 swap. I was driving the other nite and reved it to 4000rpm when it bogged out. it did this several times intermitantly. since driving the car for the first time I have always heard a popping noise from the exhaust. since it bogged out on me it sounds like...

well thanks anyways. ill figure it out.

damn that sure is alot of bullshit to get the motor rebuilt. those fuckers shoulda had it done within a month max! but goodluck come monday andrew

okay well it I didnt even bother swapping the wires. I tested the resistance of the o2 heater circuit on the o2 sensor and it turned out to be intermittantly open. so I swapped the o2 with another one I had laying around and it seems to work good now... no CEL so I hope it stays that way! as...

this is directed towards pissedoffsol's 1wire to 4wire oxygen sensor thread. I have wired up a 4 wire o2 sensor with my obd0 to obd1 conversion and I keep getting a CEL 41. my question is will this happen if I get the black wires (heater circuit) mixed up? because in his post it says it will...

no already checked that. timing belt is good. aligned the tdc mark on the crank pulley to the timing cover mark and checked the crank pulley marks for alignment. and they all line up. I know its just not going into base timing mode or adjusting mode or w/e u wanna call it.

you are supposed to jump it when timing the ignition. on my car since it is not a Si I do not have this connector.. instead I have a connector with a yellow cap on it near the drivers side motor mount. but when I jump it, it does not set base timing. therefore I cannot time my engine as anyway...