Search results

  1. F

    b18 hatch rpms bogging at idle PLEASE HELP!!!

    well i was right it didnt work it still does that just not as hard...it does it most of the time it only idles normal once in a while...im still not sure what it is i really think it is something in my vaccumes...if anybody has a vaccume diagram for a b18a1 in a 89 hatch...that would be...
  2. F

    b18 hatch rpms bogging at idle PLEASE HELP!!!

    i already did that...also i conected the fuel pressure regulator vacuume to another vacuume on the back of the intake manifold( didnt unpug it just tapped into it) and it stopped but i think thats not all when i drive it around and see if it worked for good then ill reply once again...but thanks...
  3. F

    b18 hatch rpms bogging at idle PLEASE HELP!!!

    ok i got a b18a1 89hatch, when i first start it up it idles high(2g), then after a little while it will begin to bog, like from 1200 to 1800 rpms up and down up and down. and i cant seem to figure out what it is i replaced my tps...well actually i replaced the whole throttle body cause i was...
  4. F

    B18a into 89 CRX SI wiring problems!

    ok my bad i just want to say if it is obd0 then u have nothing to worry about..just use the crx harness and thats it.
  5. F

    91 Civic SI SEATS

    yup no mods needed..
  6. F

    b16a in 91civic si axel help

    What i would do is go around to some junk yards and see if you can find the ex 4door and get all the hubs, but they are pretty rare around here i have only found a few in the junk yards..but since you got the integra hubs ready to buy...i guess i would get those you would only need to get...
  7. F

    b16a in 91civic si axel help

    I am really not to sure you might have to replace the caliper along with the hubs or maybe not if you use your rotor..u might want to ask some else about that..
  8. F

    b16a in 91civic si axel help

    yeah thats the same you do need to swap the hubs. you can either get them from a the 4 door ex which has full disc brakes all aroud which would probably be your best bet but you could just swap the front for now, you could also use 91 integra hubs but then you would have to you 14 inch wheels or...
  9. F

    B18 in 89 civic question..

    ok now i did the swap and all the wiring my self and it was all working but my check engine light was on and reading 14 which is the iac valve. Well i swapped out the valve and that is still it so i went down to the ecu and switched b2 with a11 cause i traced the wire to the comp and it was b2...
  10. F

    B18a into 89 CRX SI wiring problems!

    https://hondaswap.com/swap-articles/dpfi-mpfi-writeup-49557/ 4th Generation Civic Pages » MPFI Conversion Here ya go i think that these two should be everthing you need to do the wiring...i just did it for the first time myself...it was pretty easy i think but im just a natural i guess. oh...
  11. F

    b16a in 91civic si axel help

    What model is it cause if it is an hf then you will need to swap out the hubs, if not then you need to pry the dust ring on the innerside of the hub.
  12. F

    dohc zc swap

    well i havent talked to him yet but he sounds like he knows what he is talkin about...i would go with his advice...btw i live in philadeliphia..way to far but let me know how everything goes out... need anything else let me know...good luck
  13. F

    dohc zc swap

    Im not to sure about that...i can ask my machanic...he is a class a as the honda dealership...hell know for sure but i do know that it will work cause a pm6 is from a 88-91 si (mpfi)... which i think will work just fine but dont hold me to it cause i may be wrong...btw where r u from...if ur...
  14. F

    dohc zc swap

    4th Generation Civic Pages » MPFI Conversion https://hondaswap.com/swap-articles/dpfi-mpfi-writeup-49557/ i thought these were the best two..this is everthing u need to do...just make sure u solder all connections..ull be sorry if you dont...also i studied it for a while first...but...
  15. F

    dohc zc swap

    I know that the pm6 will work just fine...i just recently did a swap and i did all the wiring my self...i think it was pretty easy...but i also studied the diagram for weeks before i did it...need some help feel free to ask
  16. Try your Search on Google

Back
Top