Search results

  1. I<3myhonda

    PLEASE HELP!! DPFI-MPFI w/ d16z6 head swap WIRE ISSUES!

    thanks everyone for all your help and info. i couldnt have done it without you guys. it is so great i know where to turn to in a time of need. THANKS! i got her purrin like a kitten now, i had 2 wires mixed up. but thanks to everybody's quick and informative advice i got um wired up correctly
  2. I<3myhonda

    cel code 9 wire tapping?

    as title says, i just finished up my mini-me swap on my 91' Hatch (std)/d16z6/d15b2:D. ok well my ? is: i was throwing cel code 9 CYP, so i double, triple check my wiring, after doing my searching and wire checking i s:confused:... so i tapped it into b12 which i already had the other CYP wire...
  3. I<3myhonda

    PLEASE HELP!! DPFI-MPFI w/ d16z6 head swap WIRE ISSUES!

    alrighty then,.......i think i got it figured out, just disconnect the current B12 and then add C2 to the remaining wire from the plug....is that correct?
  4. I<3myhonda

    PLEASE HELP!! DPFI-MPFI w/ d16z6 head swap WIRE ISSUES!

    hi, sry but this is very ergement, im doing the dpfi-mpfi conversion at the same time as i am swaping a d16z6 head on my d15b2 91' Civic HB STD 4speed. ok so my question is: i am wirering up the dizzy and injector wires to the ecu. iv searched for days/weeks and everything says take C1-B10 and...
  5. I<3myhonda

    Help! Please help!!!

    ya, thats what im thinkin too :( i guess to try and stay positive about it, it means i have to slap my z6 head on A LOT sooner then i planned. would that also cause me to burn oil? i burn oil in high rpm's which from my knowlage is bad rings, but if it were due to the burnt valve that would be...
  6. I<3myhonda

    Help! Please help!!!

    i dont think so, but all other cyl hav tiny lash, #2 nothing at all
  7. I<3myhonda

    Help! Please help!!!

    i had replaced dizzy,cap, wires r pretty new, anyways swaped wires around made no difference, i pulled the vc off and #2 has no valve lash at all, all other cyl do but #2 dont move a mm, so im guessing valve stuck open? i pulled the spark plug and gave her a crank and a mist of fuel puffed out...
  8. I<3myhonda

    Help! Please help!!!

    bump
  9. I<3myhonda

    Help! Please help!!!

    didnt make a difference, pulled #4 plug while running and #2 plug while runnging and made no difference.. so it must be one of the injectors right? oh and now i threw a cel code 5 (map sensor) would that cause these issues?
  10. I<3myhonda

    Help! Please help!!!

    k, i tried using the plug wires from the z6 head but i know they are different bc of vtec but would it make a huge difference? or should i just swap #1 with #2 or #4 with #2?
  11. I<3myhonda

    Help! Please help!!!

    @ josh, did, and put plug in and set on frame and am getting spark
  12. I<3myhonda

    Help! Please help!!!

    pulled injectors, is the top or bottom primary? the top inj. was a lil dirty and was surrounded by gas when i pulled it. bottom one not as much. if i were to swap them would i do horrific damage?
  13. I<3myhonda

    Help! Please help!!!

    so what do i need to do to get it running ok for another few weeks so i can get the rest of the swap part together?
  14. I<3myhonda

    Help! Please help!!!

    oh and idk if i mentioned it or not but it seems to run a lil better in the higher rpms
  15. I<3myhonda

    Help! Please help!!!

    it is darker so it is gettin fouled up but i swapped in a new plug and tried again and no change, i gave it no time to foul up and still problem exist
  16. I<3myhonda

    Help! Please help!!!

    so should i take the manifold off and check/clean/replace the inj.? and this prolly sounds dumb but how do you even get to the injector/injectors? do i have to take apart the whole manifold? or is there a different way to get to it? iv been looking and dont seem to see it very clearly. got pics...
  17. I<3myhonda

    Help! Please help!!!

    no, it would start but nothing changed, no difference. cyl #2 is getting spark but no fuel. and its dpfi so atleast 2 cyl shouldnt be working
  18. I<3myhonda

    Help! Please help!!!

    bump
  19. Try your Search on Google

Back
Top