Search results

  1. E

    b16a n/a VS b20vtec n/a

    problem please are eagle ,crower,..... cranks are balanced and what should i do after i put the rods and the forged hc pistons together... it's not stroker kit but i'll buy crank eagle , rods eagel , bearings and pistons separately. do i have to go to doing balancing to this compination?
  2. E

    b16a n/a VS b20vtec n/a

    all kit balanced with every rotating assambely
  3. E

    b16a n/a VS b20vtec n/a

    what about HONDA B20-VTEC ALL MOTOR CRANK KIT
  4. E

    b16a n/a VS b20vtec n/a

    what do you think import performance parts IPP ( scat or eagle ) or crower http://www.importperformanceparts.net/
  5. E

    b16a n/a VS b20vtec n/a

    ok but light wieght full balanced stroker kit or forged full balanced stock weight ?
  6. E

    b20vtec

    hey stroker kit lighter than a stock 6lb means les tq but more revving speed (les mass more hp) and you'll need light flywheel and a light crank pully . this is my setup too or what i intend to do but if you want a light weight full balanced stroker kit then don't raise the strok make it like...
  7. E

    b16a n/a VS b20vtec n/a

    hi advise plz i don't want to turbo or any boost or raise the bore of my engine. what do you think this is my set up: i have a jdm b16a engine and i bought these stuff 68m th-skunk2 pro manifold-skunk2 pro stage 1 cams-pro gears-4.7 final gear ratio- 4-2-1 tri-y big tube header 2:5"...
  8. E

    b20 vtec stroker kit

    help please crower stroker kit with crower rods (2150$) Crower Cams & Equipment - Stroker Kits or scat stroker kit Import Performance Parts - SCAT Rotating Assemblies/Stroker Kits full ballanced kits (1600$) head mode b16a (skunk2 pro 1cams and gears , pro maifold , 68 mm th and 440 cc...
  9. E

    b16a from 10.4 cr to 11.0 cr

    i know alll this but my vtec sound is very low and the vtec work i dont know why i drived many cars with b16a and the sound of vtec is aggresive
  10. E

    b16a from 10.4 cr to 11.0 cr

    is there b16a with hi vtec sound and some with low sound
  11. E

    b16a from 10.4 cr to 11.0 cr

    before i do my setup my engine from a jdm crx b16a auto tranny model 1997 month jul i put a y21 tranny in my eg9 help with this my vtec sound is very low i don't have any ecu signal and the vtec engaged my ecu jdm p30 manual are the cams because it's from an engine was produced from the...
  12. E

    b16a from 10.4 cr to 11.0 cr

    thanks ..ill do my best
  13. E

    b16a from 10.4 cr to 11.0 cr

    i have a chipped ecu and we have a tuner with crome and we can tune to have most power of these cams but the problem is how can we adjest the degrees of the cam gears ? And if we didn't adjest the gears by putting the stock gears what'll happen? I can buy cam fixer ket but i don't know how to...
  14. E

    b16a from 10.4 cr to 11.0 cr

    so you think that skunk's pro cams will not give any power unless it tuned by a cam fixer kit or it'll give power by putting up the stock gears with these pro cams and do wide band and a chip and if i must tune gears ...what can i do we don't have any tuner here for cams
  15. E

    b16a from 10.4 cr to 11.0 cr

    hi..i have a b16a in a eg9 here is what i get to setup this engine 68 mm tb skunk2 pro manifold skunk2 stage1 pro cams 4.7 final gear ratio for y21 tranny wiseco 10.75:1 compression ratio forged pistons header and 2.5" need help about 1-do i have to get a cam fixture kit to tune my cams or...
  16. E

    b18c with b16a head

    hi i wanna do a swap in my eg9 jdm b18c block - b16b pistons jdm b16a head with stage 2 skunk2 cams , skunk2 gears ,skunk2 springs and retainers skunk2 manifol aftermarket throttle body 68m 330cc injectors header and middel pipe 2,5" and muffler crome tunning b16a tranny stage 2 clutch kit...
  17. E

    d16z6

    hi i had a d15b 3stage and the 0 to 62 m/h was 8 s now i ahve another car with d16a9 and the 0 to 62 m/h 8:45 s i am thnking to change the d16a9 with a d16z6 what do you think geys
  18. Try your Search on Google

Back
Top