Search results

  1. G

    WTB

    I am completing the last bits of a hybrid motor - a 84-87 EW series block with 86-87 Integra pistons mated with a 89 Integra D16 head (to get electronic advance and Ghd capabilities). the motor is hung and ready to fire except...I still need to obtain the Vss signal from the speedo and if I...
  2. G

    MUGEN LSD - 4.93 FD - 0.62 5th gear

    I have a MUGEN LSD in a first gen CRX/Civic tranny as well as a custom cut 4.93 FD and 0.62 fifth gear made by Jamie Houseman of Houseman Autosport. The 5th gear/FD combination yields an overall final ratio that is almost exactly the same as a stock Si , but the FD greatly improves acceleration...
  3. G

    Does vacuum line diameter affect signal strength?

    It depends on the volume of the source (log style IM, ITB with a vacuum reservoir, etc.). If you have a very large reservoir for vacuum, it will support a larger line for signal. But, the smaller line will give better response due to its lower volume...so basically pissedoffsol's analysis of...
  4. G

    d series maybe

    D Series Board Kirk
  5. G

    Mix And Match Arp/stock Headbolts

    You don't want to mix and match ARP studs/bolts with OEM studs/bolts - the clamping pressure from the ARP studs/bolts is higher. Mixing and matching would give you uneven clamping pressures across the head gasket. Kirk
  6. G

    Loud Knocking

    How Stuff Works - engines - take aread of this, you will get the general idea of how all the pieces go together. Kirk
  7. G

    Loud Knocking

    That depends on how much the motor has been run since you heard it FIRST knock...you could need a complete rebuild - I have seen scored cranks, blued rods and damaged pistons because the bearing was completely gone...I have seen a piston that has collided with the head also, so a new head was in...
  8. G

    Loud Knocking

    Take off your oil filter and open it up - see if you have metal shavings in the filter...if you do, a bearing has most likely let go. It is time to drain the oil then - metal in it? If so, bad news...drop the oil pan and start looking for the bad bearing - it is rebuild time! Kirk
  9. G

    Eagle Rods And Endyn Piston Problem..

    What kind of bearings are you using and what are the clearances you are finding? Kirk
  10. G

    1st Gen Crx Site?

    Red Pepper Racing - the 1st Gen CRX site... Kirk
  11. G

    Don't Know What To Do Now

    Take a visit here TJ's Hondasand ask -TJ, he will probably steer you in the right direction... Kirk
  12. G

    Need To Shave About 500-700 Pounds

    If you are serious about getting rid of that much weight...strip all of the interior out, carpet, seats, door panels, cut the dash to only hold your instruments, headliner - everything. Then get rid of the heater and a/c. Then get out the plasma cutter, remove all of the extra sheet metal...
  13. G

    What Are The Best Piston Rings?

    Total Seal - I don't use anything else in my high performance engines. Kirk
  14. G

    Zc Trannies

    They came as an option - TJ's Honda - you can see a write up about it there. Kirk
  15. G

    Timing Belt Repleacement

    If that belt breaks before you rebuild the motor, you stand to lose a lot more that the $$$ and time that it takes to replace it now. I have seen blocks, pistons, cranks and heads that have been rendered totally useless after a belt hase broken. It's your call though... Kirk
  16. G

    Which Cam Gears Are The Best?

    Bump for a personal friend of mine - TJ's Honda - Abjustable B Series Cam Gear Kirk
  17. G

    Need Help Shipping My Motor

    I have shipped motors to FL via DHL... Kirk
  18. G

    Need To Convert From 0bd0 To Obd1, Help!

    Take a look here...TJ's Honda - a lot of the stuff applies. Kirk
  19. G

    Help!

    The PM6 is from the 88-91 SOHC Civic/CRX, the PG7 is from the 88-89 Integra...I can't find any references to a PG6 though. Kirk
  20. G

    Standalone Cheap

    Have any of you used a SDS system...it is easy to setup and tune as a standalone engine management system. It does not require you to go purchase a laptop to program it as it comes with its own programming interface. No, it does not have datalogging - but not everyone needs it. Does it work...
  21. Try your Search on Google

Back
Top