Search results for query: *

Im stuck, thinking the dizzys would be the same bolt pattern and I could just use the dizzy from a d16z6 i had, to find it doesnt bolt up. Im putting an 88 awd wagon, taking it to obd 1 with a conversion harness and im putting a d16y7 block with a d16y8 head. Does anyone know what dizzy to use...

Issue was, the ecm wasnt grounding properly from to the main relay and wasnt grounding the fuel pump. 3 hours later from multimeter. all set no codes running like a champ.

Ill try and explain the best I can I have a b18b1 p75 manual in my 97 dx. I extended needed wires and plugs, iacv, CKF converted to a 2 plug secondary O2 wired. Now when I tried to start it orignally it started and ran pretty well but was throwing code 54 which is CKF sensor. I read all over and...

converted the 3 wire to the 2 wire plug, everything is connected and im still getting the code, is there something else I need to do? Wait? Reset ecu? Or am I left with the trick to bypass the code and get its signal from c4 and c14 the cyp or something?

I was wondering if someone could clarify that obd2a with the 99s and obd2b with the 96's. I have a ecu from a 99 ls that is the exact same as my p2p and p72 which are both obd2, so i thought the obd2b was a different pinout? After looking at it i will be able to use the p75 on my 97 civic hatch...

I have a 97 civic dx, looking to put the ls in it

Anyone give me a quick clarification? I have a full ls car, all parts, If so I can use the LS rear tranny bracket, or Do i need to get the si tranny bracket and si shift linkage, I have LS everything. Thanks guys.

That solves a lot of problems... :rolleyes:

After getting the readouts, I get a secondary o2 sensor, and a evap high message. I bought the secondary o2 and got wire to manually run it, i just need the pins that plug into the ecu so i can solder those to the wire and plug them into my ecu. As for the evap, I dont know whats causing...

My 88 AWD wagovan :( So yesterday I just got the motor in, did all the pluging in of connectors and what not to get the motor up to a starting point. Cranked it over to build oil pressure. Then connect up the plugs and turn it over with no luck, it sadly sounded like the d16a6 i pulled out with...

I see the spot of where it goes, but there is no connection in the wiring other then one connector that doesnt look like the right plug? it only has 2 wires on it?? The o2 sensor has 4 wires...?

If I were to have the y7 harness, is there a plug for the secondary O2? or is there only one in the y8 harness? If I have the y7 harness do I have to manually wire into my ECU the wires for the secondary O2? How do I know which Harness I have in my car? I bought it the way it is, with the...

So the guy made a mistake... come on we arent here to flame and make fun, we are here to help him make better choices for next time and get him on the right track. But yes, sadly you probably got taken by some asshole... what good people we have in this world. Anyways, try and sell what you can...

just got the motor mount from drivers side d16a6 over to the d16z6 and all plastics and back together, just need to mount up the tranny, half shaft, and its ready to drop back in, and plug things in :) pictures coming soon!

Okay this project has been started and as of right now the engine bay of the 1988 is cleaned out, the motor is out, the crank pulley off both motors to swap the drivers side motor mount. What I have left Swap the motor mount to the d16z6 put the casing back on and crank pulley. put oil in plug...

How much for both shipped to 84047?

I got it all swaped minus a drivers side e brake, on the passenger side its an integra, but it measured shorter then the civics drum??? Should I buy another integra? or do i swap the passenger out for other e-brake cables??? Thanks guys I searched the forums, and looks like i may just buy...

I have thought about a book or a site that you can go to with step by step free instructions on how to do stuff to your civic, such as head gaskets full swaps, rear discs, all the cool stuff, so if your needing help on anything there is pictures and how tos on it all. I learn best when I can...

I need a VSS please anyone have an extra list your price shipped to 84047 please!!

Greatly appreciate everyones help here with questions and answers to all my many problems, Just last night at around midnight on my 97 ek hatch silver type R replica, i completed a read disc setup with blox lca and camber kit and hand r springs. With all your help I did it flawlessly minus...