Search results for query: *

Recently I rebuilt my B18B1 in my 98 Acura integra LS and so far have around 700 miles on it and am planning to change the oil next. Just out of curiosity I seem to have gone thru maybe a little less then a half a quart of oil, I know that oil consumption is normal, but is this amount normal on...

My power steering pump is sounding like it may be going out and has been for awhile, has anyone ever rebuilt one of these before? easy, hard?

If the car is totaled, insurance companies I can only assume they could care less. They have to give you what it was worth before the accident so you are not at loss after the accident and are able to purchase a comparable vehicle. They use stuff like NADA or their own hybrid version of it to...

thanks everyone, reps given......

I used a non honda power steering fluid (prestone), will it harm the system? if it is bad how do I get it out? 1998 acura integra LS

Well I replaced the TPS but I doubt it was that, instead it turned out that I was one tooth off on the cam pulleys, I did not see the two marks on the cam pulley that needed to be aligned, so the timing was out. The big giveaway was when I advanced the timing and checked it with a timing light...

I cleaned them with Gasoline and no I do not have anyone with a throttle body that I can borrow from, sure wish I did....

I did try to adjust the TPS in the closed position and could not get it within specs. The engine is stock and was honed, all I did was put new rings, rod bearings, main bearings, and new oil pump in it. Also I head the head reworked while it was off. I am still using the old fuel filter which...

I checked the TPS today via Helms manual. TPS seemed to be out of the required service, limits. I ordered a new one today. If this does not fix the problem then what else other then timing and cables could I look at? Is it possible I could be one tooth off on the cam pulleys, could this cause this?

1998 Acura Integra LS B18B1 I just rebuilt my engine and fired it up tonight for the first time. It seems to idle fine and I have good oil pressure 60 psi at 2000 rpm. The problem I am having is that when you open it up there is a lot of delay before the engine revs. What could be causing this...

Thanks for your help, this is my first motor so I want to make sure I do not miss any thing along the way, thanks again

I went on NPR website and can not find information on what they recommend, would I have to file these rings to fit or since they are standard rings would they be a direct fit?

Ordered NPR rings hopefully I can find the info on their site. Was affraid the honning may have took too much off , guess the rings will tell the story. If ring gap is out of spec then would I have to look at boring it or going to a different set of rings?

I have a B18B1 engine and am wondering what clearances others are running in their honda/Acura. I just had the block honed and want to make sure that I will not have problems with stock rings. I was told that it is .003 piston to wall and I am running the original stock cast pistons.

Thanks for posting this, I will try to make heads or tails out of it, I am sure it will help a lot on trying to figure this out.

I posted this over in the engine section instead

Also any idea about the sealant I need for the bearing housing and the oil pump, Indian head shallack, rtv, or?

The manual says "published by Honda Motor Company" I bought it right after I bought my Integra back in 1997 in the parts dept of Tustin Acura, I have used it extensively, so much pages are falling out. So I have the bearings and I am assuming they are the one size fits all, since there is...

I am building a B18B1 and this is my first attempt at it, and do not want to screw it up. I have a few questions and hope someone can help: Questions: 1. I am reading the service manual and I am trying to install the pistons, reading the section in the manual it states that there is a number...

I am building a B18B1 and this is my first attempt at it, and do not want to screw it up. I have a few questions and hope someone can help: Questions: 1. I am reading the service manual (same that they use at dealership) and I am trying to install the pistons, reading the section in the...