Search results

  1. E

    block internals compatibility

    no we installed the a6 engine with y8 head as it came but we put the y8 intake from the blown motor on the a6 because of the injector clips not working with the obd1 injectors. im going to have a go at making it work on the weekend. recap: 2000 si, D16a6 with y8 head, y8 intake, p28 ecu...
  2. E

    block internals compatibility

    we installed the d16a6y8 into the 2000 si but cant get it to run. ive done a b18a1 swap into my 90si but this is proving to be a bitch. its been sitting for a year now and ive kinda forgotten about it. its not my car. in the car now is a d16a6 with a y8 head and a y8 intake. not sure what dizzy...
  3. E

    block internals compatibility

    i have a d16a6 with a y8 head built for turbo. i also have a stock obd2 d16y8 with a blown bottom end. can i swap the crank/ rods and pistons from the d16a6 into the d16y8 to make the d16y8 turboable?
  4. E

    3000rpm cold idle

    i have a 90 si hatch with a 91 b18a1, had the engine in for a few months now but since day one its had a cold idle of around 3000 rpm. i really dont think its supposed to be that high but i could be wrong. the car idles just fine at 700 rpm when warmed up, ive cleaned the iacv and replaced the...
  5. E

    91 hatch need help please

    sounds like a plugged fuel filter
  6. E

    b18a1 surging at speed...

    it's a 90 si hatch with a 91 b18a1, new dizzy, new sparkplugs, new wires, new fuel filter, straight swap, engine has DC 4-2-1 headers, no cat, 2inch pipes into a flowmaster muffler, grounds are good (no paint/rust) what is an "Orig pump"
  7. E

    timing

    jumping the conector under the glovebox didn't change the timing on the light. isn't the tdc pointer supposed to move from the red line to the white line when you remove the conector? the tdc pointer stayed on the red line with or without the conector jumper
  8. E

    b18a1 surging at speed...

    cruising at highway speed 3000-3500 rpm the engine surges about 50 rpm every 2 seconds or so. it seems to have a rythem to it. the engine seems to run good otherwise. it has done it since the install (90si h/b) about 3 weeks ago. any ideas anybody?
  9. E

    no cooling system pressure...help?

    yeah i did everything propper like, got is sorted, turns out it needed to be loaded up to get that extra bit of heat into it, 20 min idle wasn't enough
  10. E

    no cooling system pressure...help?

    90 si with b18a1 newly installed, new rad, new rad cap, new heater core, new w/pump, new t/belt, new t-stat, no external leaks, no milky oil, no white smoke out the pipe!! HELP!!!!!!!
  11. E

    clutch cable

    my 1991 integra cable appears to be just a tad too short as i have the adjuster nut backed all the way off and its not releasing the arm into free play, the tranny is an unidentifiable '92 or '93 tranny (found that much out the expensive way, goddam splines!!). i have cross referenced honda part...
  12. E

    cold air intake?

    does anyone know what air intake i can use for my ef b18a1? iv'e found and aem product no. 21-5001C but they say it only fits the b16a and b18c5. i don't want to move the battery. what have you guys used? thanx
  13. E

    cat elimination, what to do?

    :) close but not really what i was getting at :)
  14. E

    cat elimination, what to do?

    im building a stock b18a1 ef si with dc 4-2-1 header and dynomax DNX mid pipe and flowmaster muffler. i want to eliminate my cat but i'm not sure if i should make a custom pipe or if there is a test pipe that will fit in place with no mods. anyone done this/ know what i should do?
  15. E

    EF ls swap question!?

    is the map sensor on the tb plugged in? if not then the plug you are looking for isn't on the engine harness, it breaks out around the passenger shock tower/ fusebox, its a 3 pin plug with a green/white, white and yellow/red wires
  16. E

    tranny input shaft headache

    yeah i just compared the '91 clutch kit i bought to the same spec clutch kit from the same manufacturer for the '92 and '93 and the only difference is the disc itself. i don't know why i didn't think to do that first
  17. E

    tranny input shaft headache

    i bought a cable trans form a guy who told me it was from a 91 teg, so i purchace an ACT clutch kit for a 91 teg, i go test fit the clutch disc on the input shaft and to my suprise , it does not fit... therefore i have a 92 or 93 cable trans. my question is... can i just use a clutch disk for a...
  18. E

    which exhaust?

    thanks for the info, im going to use this Dynomax Performance 17452 - Dynomax Super Turbo Exhaust Systems - Overview - SummitRacing.com and this DNX 38212 - Dynomax DNX Mid-Pipes - Overview - SummitRacing.com to start with
  19. E

    steerin wheel vibration - axles?

    not sure how long the bend is but at 60mph im in it for about 6 or 7 seconds. i have removed the doughnut as the rubber had deteriorated, made no difference, i have checked for play in the tie rods, they're good, i have not done an alignment yet but will soon, next time im at the shop im gunna...
  20. E

    90 civic si rear drum conversion help

    cut the bolt with a hacksaw between the shock and lca bushing, once cut (you might need to do both sides) it will seperate, replace the bushing, dont bother trying to get the bolt out of the bushing
  21. Try your Search on Google

Back
Top