Search results for query: *

I have questions about the pilot bearing for my 97 Accord. I took the Fidanza flywheel to get resurfaced. When I got it back the guy at the machine shop handed me the pilot bearing and said it just fell out when they resurfaced the flywheel. I thought the pilot bearing was supposed to fit into...

Does anybody know of a header that properly fits the 91 crx with a B16a swap. The header that I have hits the cross member. It’s a 1 pieace 4 to 1 header. I had to cut out more than half of the cross member in the center so the header would clear it. I understand having to shave a little bit off...

I need to know if I am supposed to use the retainer clips from the factory lower ball joint boots with the energy suspension boots. I tried to put one of the retainer clips on the energy suspension boots but they won't stay in place. They will move around and fall all they way down. I noticed...

My 97 Accord is a manual 5 speed transmission. It will not shift gears while the car is running. When the car is not running I'm able to shift in and out of all of the gears. I have replaced the slave cylinder and clutch master cylinder twice. I have blead the lines throughly many times. The...

My 91 Crx (b16a) will not turn over or start. Here's what's been checked. 1. Battery is good 2. Starter is good 3. Ignition switch is good 4. Starter relay is good, starter fuse is good 5. Battery ground is good 6. No spark from the distributor. I bought a new one and no spark from the new one...

I have a 97 Accord with a 5 speed manual transmission with shifting problems. It will not shift into any gears while the car is running. The shifter is stuck when the car is running. If the car is not running it will shift into all gears with no problem. What is causing this problem????????

I just bought and installed a rebuilt manual transmission for my 97 Accord. It will not shift into reverse at all. It will shift into all of the other 5 gears with no problem. What is causing this? Can this be repaired without removing the transmisssion again?

I'm having a crazy idle problem with my crx si. The idle is very high and constantly going up and down and staying between 2000 and 4000 rpm. I disconnected the battery and reconnected it a few times to reset the ecu but this problem will not go away. What is causing this????????

I need to know if the ignition coil out off a TD42U distributor will work in a TD44U distributor. The TD42U distributor comes on a sohc d16z6 engine, and the TD44U is what my B16a uses. The ignition coil on my B16a didn't pass the resitance test and I was wondering if the coil from the TD42U is...

My 91 CRX wont start. All I get when I turn the key is a buzzing sound, and I can hear the fuel pump turn on. I pulled the starter and battery off and had them both tested and both tested good. I have tried another ignition switch, main relay, starter relay, and clutch switch. The car still will...

I'm having some weird electrical problems in my 91crx. The lights in the middle of the gauge cluster for the e-brake, door, trunk and seatbelts stay on all the time with the car off and no key in the ignition. I even disconnected the igniton switch and all of these lights still stay on. If I...

I think I may have the wrong axle on the right\passenger side of my crx. The car rides fine with this axel but I noticed some oil around the inner part of the axel where it goes into the tranny. To me it doesn't look like the axel is all the way flush with the tranny. I have it in as far as it...

I just got my crx running monday. It's running good but the check engine light is on. The code is for the knock sensor. Im trying to find out where to connect it. My car is a 91 crx si with the obd1 jdm b16a.

I'm trying to find out if the ecu posted below is for a manual transmission or automatic transmission. The person that sold it to me on ebay said it's for a manual transmission. I'm thinking it's for an automatic because it gave a code 19 which is automatic transmission related in the haynes...

Are the distributors different for B16's with automatic and manual tranny's like the D16's are or are they the same? The distributor on my B16 is TD44u. The jdm B16 I have was originally mounted to an automatic tranny when I got it. I'm using a manual 5 speed tranny. I'm thinking that may have...

I finally got my B16a into my 91 crx si. It's turning over but will not start. Everything is connected correctly, battery is fully charged, brand new starter, brand new plugs & wires, and I can hear the fuel pump when the key is in the on position. I'm using the same p28 ecu that I used on my...

I'm STUCK in the middle of doing a B16a swap in my 91 crx si. The car is jacked up with the engine still on the engine lift hanging in my engine bay with only one side mounted up:mad:. It's the 2nd gen OBD1 B16a. I'm only able to get the right side (transmission mount) bolted up in the car. I...

Is it possible for an AEM fuel rail and fuel pressure regulator for a D16 engine to work on a B16 engine?

I have the 2nd gen B16a SIR2 engine with a hydro tranny converted to cable. I just found out that the half shaft from a 90 integra will not work:mad::mad::mad:. The half shaft will not go all the way into the tranny. It sticks out about a 1/4 of an inch. Now I need another half shaft, and more...

I'm putting my B16a in my 91 crx si tomorrow. It's the OBD1 sir2 B16a. I've already been converted to OBD1 with the sohc vtec (A6 block Z6 head)that I'm pulling out of the car. I was using OBD0 injectors with this setup. I'm planning on using the OBD1 injectors that came with the B16 I have. Do...