Search results

  1. H

    95 d16z6 into 93eg 4 door won't rev but.....

    I checked all the connection, sensors, and vacuum lines and everything is correct. Just afew minutes ago I took out the top bolt on the fuel filter and trie to put in a fuel pressure gauge but the threading was different. I drove it to the store and when I came out it wouldn't start and it...
  2. H

    95 d16z6 into 93eg 4 door won't rev but.....

    gotta figure this out cause ive got a ram horn turbo kit on the way and already have the 550 injectors. It works for a B-series so if all else fails.... Found a 94 ex sedan with blown head gasket for 800 and actually considering getting it so i can side by side part swap.
  3. H

    95 d16z6 into 93eg 4 door won't rev but.....

    getting closer Tried another z6 dizzy and same thing it will rev to redline sitting still with just a burp. Driving down the road it won't flat out accelllerate and you have to wean the throttle past about 3500 to 5000 rpms. Any Ideas? Still no CEL
  4. H

    95 d16z6 into 93eg 4 door won't rev but.....

    found most of the problem Got the car to rev sitting still. The distributor was apparanetly bad maybe the CPS or something. I stuck a D15 non vtec on it even though it wouldnt bolt up and it fired and revves great. Took the insides out and transfered it to my dist housing. Now it just has a...
  5. H

    95 d16z6 into 93eg 4 door won't rev but.....

    no change just louder! I put straightpipe all the way back to a resonator with a baffle. I had it from NOPI about 7 years ago still in the box. Loud as hell but no change. I guess it could only be the distributer then.....or my ecu has went bad!?!? im sick of part hanging. if im gonna kep...
  6. H

    95 d16z6 into 93eg 4 door won't rev but.....

    probably will so I'll know faster but I have a new header to put on it so I might just hang it and not connect the cat and cross my fingers. I decided to start it and get it warm to melt out any ice that might be in the system so I could drain it and put in antifreeze bc it's down to 12 degrees...
  7. H

    95 d16z6 into 93eg 4 door won't rev but.....

    My catalytic converter is glowing Could that have been my problem the whole time??????????A stopped up cat
  8. H

    95 d16z6 into 93eg 4 door won't rev but.....

    what would cause my fuel pressure to be 80psi? I've took off the adj regulator and tried oem regulators but nothing will decrease the pressure. I think the problem might be too much fuel. It idles perfect but any gas and it boggs so that's the only thing left that it could be.
  9. H

    95 d16z6 into 93eg 4 door won't rev but.....

    might still be but I'm stumped so far. MERRY XMAS
  10. H

    95 d16z6 into 93eg 4 door won't rev but.....

    I converted to a 5speed while I was at it. Where it was wrecked I had a TPS code because it got smashed and an o2 sensor code same reason. Replaced the 3hrottlebody off of a running 95 z6 and no codes. I have sprayed ether around the engine(while cold of course) and I couldn't find any intake...
  11. H

    95 d16z6 into 93eg 4 door won't rev but.....

    I can't think of any other vac lines to check. The valve cover one has a mini filter on it and the intake has one too
  12. H

    95 d16z6 into 93eg 4 door won't rev but.....

    the IACV goes to the bottom of the TB. Can't remember where the top TB hose goes
  13. H

    95 d16z6 into 93eg 4 door won't rev but.....

    nope. The FPR just goes straight into the intake. It's only about 6in long.
  14. H

    95 d16z6 into 93eg 4 door won't rev but.....

    my evap purge valve has been JB Welded in the past. If it's leaking air then would that cause the 80psi fuel pressure?
  15. H

    95 d16z6 into 93eg 4 door won't rev but.....

    the engine I took out ran fine except for a blown head gasket. Lol so the fuel system should be ok from the filter back. It was a D15something y5? I'm using the fuel filter from it. Surely that wouldn't matter this much. I just added a gauge on top.
  16. H

    95 d16z6 into 93eg 4 door won't rev but.....

    the vac line goes from the FPR into the intake. The evap purge on the firewall side goes to the canister. The other canister line goes to the TB. I'm pretyy sure that's how it's ran. I didn't unhook them when I swapped engines. I didn't use the same canister but the lines were only long enough...
  17. H

    95 d16z6 into 93eg 4 door won't rev but.....

    the ecu, harness, and engine came out of a civic I totalled and it is all for a 5 speed and it ran like a champ before I yanked it. It has to be the fuel pressure but what would cause the pressure to be 80 all the time ? I have tried oem regulators that I know were good. It had an adjustable FPR...
  18. H

    95 d16z6 into 93eg 4 door won't rev but.....

    still cant figure it out. It boggs if you give it gas, Running 80 psi even with oem fuel pressure reg . Is there a relay under the dash(besides the ecu) that could be causing the problem? Any pinouts I should check to make sure it is right. I have a P28 and then bought a 95 civic ex to...
  19. H

    95 d16z6 into 93eg 4 door won't rev but.....

    it idles absoluttely perfect and i ran it for an hour tonight but it wont rev!!!
  20. Try your Search on Google

Back
Top