Search results for query: *

Hey, Im pretty stumped too... bah.. I hard-Wired Vtec to a switch. (Solenoid -> Switch, Switch-> Power) I heard vtec for the first time for about 10 times(Only engaging it after 5000RPM). Now it wont work even with the switch, I hear the click everytime (Had someone inside turn the...

Really.. nothing guys??!

Hey guys, Yes I have done a LOT Of searching and for some reason I still cant resolve this problem. P06 Chipped to P28 w- Vtec. Vtec engage - 4600, Disabled Knock sensor. No CEL Codes. Vtec oil pressure sensor to D6 Ground to Chassis Vtec solenoid to A4 Oil is topped up, no...

Problem Resolved... idiot Mistake.. When i remove the alterntator, I forgot to bolt back up the halfshaft for the axles. Epic fail. Lol

Hey Cafrog, Thanks for taking the time in lookin into this, you've helped me before and its really appreciated. I just had the flywheel Resurfaced and a brand new clutch(650KM so far) into it, also replaced the throw bearings, etc full clutch kit. The reason the starter went is because it...

Alright man, I will check my fluid today, I just filled er up 2 weeks ago. Will post an update tonight :)

Also when I give it gas it any gear or neutral, it revs so quick and the actual speed sky rockets to like 200km lol..

Hey guys, Not going to bore you all with a long story... situation: Starter bolt bracket broke, so JB welded the bracket back on, replaced, started fine, was driving down the highway and hit a bump, all of a sudden now... Car in ANY Gear = NO movement.. When using the gear shifter it just...

To follow up on this matter; Issue Resolved: Fix: Alternator was dead. The alternator Diode was leaking and pulling amps from the battery when the car was off. Symptoms: If the lights get brighter as you rev the engine, it means the alternator is producing some current, but may not be...

Definetly going to have that tested, still curious as to why the headlights turn off though (Even when Positive wired to battery and Negative to the harness) the light still turns on when the RPMs are gained. I might try wiring the negative to the battery aswell to see if the problem persists...

Codes Were 20 and 22, Electronic Load Detector and the Vtec (wasnt Wired yet)

Thanks so much for the replies guys, now I took off the little red thing to disable my chip for my ECU and the car starts/runs great now.... BUT. I checked the thermostat ground, it seeems fine, sanded it down.. OK. BUT, when the battery light is still on but the battery doesnt seem to be...

Hey Guys, To follow up, Replaced Clutch and had Flywheel(That had like a 4mm groove.. shot) Resurfaced, Problem is now resolved. Updated thread so others with the probelm will be able to know that it was successful with a resurface to fix that probelm. Thanks guys, ~josh

Hey guys, Im running into a bit of a bit of a, what seems like electrical problem.. Here's the beginning. Engine was Slipping like crazy(worn out flywheel), and then one day the battery died completely, so I took it into the garage.. took apart the tranny using the G3 Clutch change DIY Guide...

Most definetly, I will update this when I get out of work with the codes it is throwing :D

Hey man, Thanks a lot for all of the information, I do appreciate it a lot, believe me. I will be taking the car into the shop to get all 3 replaced, might aswell since it will be accessable =). Thanks a lot E Solsi

The Clutch.. Hmm I know about a week and a half ago I replaced the Slave Cylinder, becuase it was done for, and since then the clutch has felt strong, it goes into gears fine, would that be a problem with Rising in RPM but not speed, and then balancing itself out? Its a strange problem, usually...

Im not actually sure about the CEL, when I had the P30 in it(Just to check codes), the only codes it was throwing was Vtec Solenoid(Becuase it was not hooked up). I have not yet had the Vtec working in this car yet although it is wired to work, also forgot to mention that it is running really rich.

Hey guys, Ive been searching for a little over a week in regards to what my problem can be. The car will be going to a shop on Friday, but im trying to avoid the 85$/HR. I am running a JDM B16A (2Nd generation OBD1). I have a P06 Chipped to P28 with Vtec. CEL is on, always has been since...