1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

94 civic ex b16a2 swap

Discussion in 'HYBRID -> EG-EK / DC' started by VTECPOWER, Jan 29, 2004.

  1. VTECPOWER

    VTECPOWER Senior Member

    Messages:
    1,683
    Likes Received:
    0
    Joined:
    Oct 6, 2003
    Location:
    Winchester, VA
  2. civicious

    civicious FüK-VTEC VIP

    Messages:
    9,855
    Likes Received:
    629
    Joined:
    Jun 15, 2003
    Location:
    Houston, TX
    :readfaq:
     
  3. scottp11

    scottp11 The Seniorest Member....

    Messages:
    987
    Likes Received:
    4
    Joined:
    Nov 20, 2002
    Location:
    El Paso, TX now, originally from Fresno, CA
    hmotorsonline does not sell B16A2 motors... USDM.
     
  4. VTECPOWER

    VTECPOWER Senior Member

    Messages:
    1,683
    Likes Received:
    0
    Joined:
    Oct 6, 2003
    Location:
    Winchester, VA
    on the website it says both USDM and JDM
     
  5. VTECPOWER

    VTECPOWER Senior Member

    Messages:
    1,683
    Likes Received:
    0
    Joined:
    Oct 6, 2003
    Location:
    Winchester, VA
  6. slick*vic*

    slick*vic* Member

    Messages:
    96
    Likes Received:
    0
    Joined:
    Oct 30, 2003
    its the sir-II. yes that is pretty much everything you need. Use you stock eng harness and wire up the knock sensor to the ecu. You will have to extend the vtec wires so the connectors will reach. Other than that its a fuck'n breeze. Good luck

    P.S get the fuck'n LSD. dont be a cheap bastard
     
  7. VTECPOWER

    VTECPOWER Senior Member

    Messages:
    1,683
    Likes Received:
    0
    Joined:
    Oct 6, 2003
    Location:
    Winchester, VA
    do u think i would be able to do the swap in my garage over a weekend?
    or how long do u think it would take.
    also, how much would it cost to have a shop do it
    i live in northern va

    what will i have to do with the wiring?
     
  8. slick*vic*

    slick*vic* Member

    Messages:
    96
    Likes Received:
    0
    Joined:
    Oct 30, 2003
    Well the tim lengths of the swap has many factors. How mechanically incline you are, whats your tool situation. If you have one of your boys help'n. So if your do your homework and plan shit out(everything you need) it should go pretty good. The wiring is simple, you have to add 1 wire from the knock sensor which is located above the oil filter. Run that wire through the firewall(keep it clean) to the ecu..check refference for pin #. you will also have to extend the vtec wires because the vtec pressure switch and soleniod are on the opposite side of the distributor. Good luck
     
  9. Cashizslick

    Cashizslick !i!i!i!i!i!i!i!i!i!i!i!

    Messages:
    5,751
    Likes Received:
    37
    Joined:
    Aug 15, 2003

    Hmotors online is mad ghey - forget getting a mystery motor.
     
  10. xj0hnx

    xj0hnx I wanna be sedated VIP

    Messages:
    14,172
    Likes Received:
    48
    Joined:
    Nov 10, 2002
    Location:
    C.C.TX.

    You're an idiot. Hmotorsonline is one of, if not the best place on line to get motors. Just because you couldn't figure out how to wire your car, doesn't reflect on them.
     
Verification:
Draft saved Draft deleted

Share This Page