1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

chipping gone bad?

Discussion in 'ECU's, Electronics, and Tuning' started by gatto-is-alive, Aug 5, 2009.

  1. gatto-is-alive

    gatto-is-alive New Member

    Messages:
    118
    Likes Received:
    0
    Joined:
    Jun 18, 2008
    Location:
    EARTH
    :(i have just chipped my pr3 obd1 ecu and now the car wont rev pass 4k any ideas??

    i got the eprom programmed for a p30 because i cant find anyone that has the pr3 obd1 programme
     
  2. DESPAIN

    DESPAIN yep....mmhhm.......yep...

    Messages:
    1,703
    Likes Received:
    39
    Joined:
    Aug 1, 2008
    Location:
    flower mound TX
    well it sounds like its in limp mode
     
  3. Briansol

    Briansol Admins Admin VIP

    Messages:
    21,448
    Likes Received:
    2,110
    Joined:
    Nov 18, 2007
    Location:
    CT
    uhhhhhhh where did you find an obd1 pr3?
     
  4. gatto-is-alive

    gatto-is-alive New Member

    Messages:
    118
    Likes Received:
    0
    Joined:
    Jun 18, 2008
    Location:
    EARTH
    the obd1 pr3 came off a JDM 93 teg xsi

    what is the limp mode?? can i get my ecu run normally or ??????
     
    Last edited: Aug 6, 2009
  5. DESPAIN

    DESPAIN yep....mmhhm.......yep...

    Messages:
    1,703
    Likes Received:
    39
    Joined:
    Aug 1, 2008
    Location:
    flower mound TX
    limp mode is when your computer shuts down into a "safe mode" are you throwing any codes?
     
    1 person likes this.
  6. gatto-is-alive

    gatto-is-alive New Member

    Messages:
    118
    Likes Received:
    0
    Joined:
    Jun 18, 2008
    Location:
    EARTH
    i dont know i dont even have the check engine light wired up

    do you know the pin outs for it??
     
  7. gatto-is-alive

    gatto-is-alive New Member

    Messages:
    118
    Likes Received:
    0
    Joined:
    Jun 18, 2008
    Location:
    EARTH
    i think that an eeprom that has an obd1 programme must work with any obd1 ecu right no matter the p's
     
  8. rfrumusa01

    rfrumusa01 Bean Cakes

    Messages:
    60
    Likes Received:
    0
    Joined:
    Nov 12, 2007
    Location:
    Rochester, NY
    I have never heard of anyone ever chipping a PR3...
     
  9. gatto-is-alive

    gatto-is-alive New Member

    Messages:
    118
    Likes Received:
    0
    Joined:
    Jun 18, 2008
    Location:
    EARTH
    well maybe that i m the first one to do it but i need help for it to finish the job
     
  10. DESPAIN

    DESPAIN yep....mmhhm.......yep...

    Messages:
    1,703
    Likes Received:
    39
    Joined:
    Aug 1, 2008
    Location:
    flower mound TX
    did you ever run the cel codes?
     
Verification:
Draft saved Draft deleted

Share This Page