1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

JDM B16A Pistons on LS Rods

Discussion in 'Parts: For Sale/Trade/Wanted' started by lsvtec, Oct 28, 2003.

  1. lsvtec

    lsvtec GNU/Linux Evangelist

    Messages:
    5,453
    Likes Received:
    3
    Joined:
    Sep 30, 2002
    Location:
    Greater Portland, OR
    As the title says JDM B16A pistons already pressed on B18A1 rods the rods are out of a 93 Integra, the pistons are out of a longblock purchased from Japan. SOLD

    Inlinefour.com stiffened inner valve springs. They have been run for about 2000 miles I have upgraded to Skunk2 Springs. SOLD.

    I would prefer a Money Order or a Cashiers check.

    EDIT: Lowered pistons/rods price

    EDIT: Marked inner valve springs as sold.

    EDIT: Marked Pistons/Rods sold.
     
  2. lsvtec

    lsvtec GNU/Linux Evangelist

    Messages:
    5,453
    Likes Received:
    3
    Joined:
    Sep 30, 2002
    Location:
    Greater Portland, OR
    Bump
     
  3. GSRCRXsi

    GSRCRXsi Super Moderator Moderator VIP

    Messages:
    9,622
    Likes Received:
    345
    Joined:
    Nov 13, 2002
    Location:
    MD
    do the pistons have rings on them? and are the pistons used?
     
  4. lsvtec

    lsvtec GNU/Linux Evangelist

    Messages:
    5,453
    Likes Received:
    3
    Joined:
    Sep 30, 2002
    Location:
    Greater Portland, OR
    They have Total Seal rings but those rings were in my engine for ~1200 miles. They came out of a JDM engine soe they are used like anything else that came from Japan. Plus they spent ~1200 miles in my LS engine before I went with forged internals.
    EDIT: the rods come with the end caps.
     
  5. GSRCRXsi

    GSRCRXsi Super Moderator Moderator VIP

    Messages:
    9,622
    Likes Received:
    345
    Joined:
    Nov 13, 2002
    Location:
    MD
    but could those rings be reused?
     
  6. lsvtec

    lsvtec GNU/Linux Evangelist

    Messages:
    5,453
    Likes Received:
    3
    Joined:
    Sep 30, 2002
    Location:
    Greater Portland, OR
    I am not sure. Anyone know the answer here?
     
  7. lsvtec

    lsvtec GNU/Linux Evangelist

    Messages:
    5,453
    Likes Received:
    3
    Joined:
    Sep 30, 2002
    Location:
    Greater Portland, OR
  8. hybrid_b18

    hybrid_b18 crew chief

    Messages:
    254
    Likes Received:
    0
    Joined:
    Sep 24, 2003
    Location:
    Burnsville, MINNESNOWTA
    yO. so i can out these pistons in my 96 b18b1? wont i have blow-by?
    :D
     
  9. lsvtec

    lsvtec GNU/Linux Evangelist

    Messages:
    5,453
    Likes Received:
    3
    Joined:
    Sep 30, 2002
    Location:
    Greater Portland, OR
    These pistons are for an 81mm bore, if you are over bored your block then they will not work. Other than that I can't under stand what you are trying to say.
     
  10. saturn_boy96

    saturn_boy96 88 C1V1C 53D4N DR1V3R

    Messages:
    1,507
    Likes Received:
    1
    Joined:
    Dec 13, 2002
    Location:
    Sheridan, WY
    will those inner valve springs work on a non-vtec head?
     
  11. lsvtec

    lsvtec GNU/Linux Evangelist

    Messages:
    5,453
    Likes Received:
    3
    Joined:
    Sep 30, 2002
    Location:
    Greater Portland, OR
    According to inlinefour.com they will work with any B or H series head.

    EDIT: inlinefour has them for $40 a side, $30 bucks gets all 16 shipped to your door.
     
  12. lsvtec

    lsvtec GNU/Linux Evangelist

    Messages:
    5,453
    Likes Received:
    3
    Joined:
    Sep 30, 2002
    Location:
    Greater Portland, OR
  13. lsvtec

    lsvtec GNU/Linux Evangelist

    Messages:
    5,453
    Likes Received:
    3
    Joined:
    Sep 30, 2002
    Location:
    Greater Portland, OR
    Bump for lower pistons/rods price.
     
  14. saturn_boy96

    saturn_boy96 88 C1V1C 53D4N DR1V3R

    Messages:
    1,507
    Likes Received:
    1
    Joined:
    Dec 13, 2002
    Location:
    Sheridan, WY
    bump for an amazing price.
     
  15. lsvtec

    lsvtec GNU/Linux Evangelist

    Messages:
    5,453
    Likes Received:
    3
    Joined:
    Sep 30, 2002
    Location:
    Greater Portland, OR
    Bump, this is a good deal for anyone building a high compression LS bottom end.
     
  16. saturn_boy96

    saturn_boy96 88 C1V1C 53D4N DR1V3R

    Messages:
    1,507
    Likes Received:
    1
    Joined:
    Dec 13, 2002
    Location:
    Sheridan, WY
    i am still interested in the inner valve springs. pm me with your info so i know where to send the money. MO okay?
     
  17. lsvtec

    lsvtec GNU/Linux Evangelist

    Messages:
    5,453
    Likes Received:
    3
    Joined:
    Sep 30, 2002
    Location:
    Greater Portland, OR
    You've got a PM.
     
  18. saturn_boy96

    saturn_boy96 88 C1V1C 53D4N DR1V3R

    Messages:
    1,507
    Likes Received:
    1
    Joined:
    Dec 13, 2002
    Location:
    Sheridan, WY
    bump, and i'm sending the money order today for the springs today. :)
     
  19. lsvtec

    lsvtec GNU/Linux Evangelist

    Messages:
    5,453
    Likes Received:
    3
    Joined:
    Sep 30, 2002
    Location:
    Greater Portland, OR
  20. lsvtec

    lsvtec GNU/Linux Evangelist

    Messages:
    5,453
    Likes Received:
    3
    Joined:
    Sep 30, 2002
    Location:
    Greater Portland, OR
Verification:
Draft saved Draft deleted

Share This Page