Search results for query: *

This test was done after driveing for about and hour. I used a dual gauge tester. Has the PSI supplied and leakdown percentage. Cylinder 1,2,4 had 15% leakdown, droped 3-5psi on each. Cylinder 3 had 35% leakdown with a 5-7psi drop. No air comeing out the intake or tailpipe. You could hear it...

I have an 88DX with a Z6 swap. I had my head Ported by a local shop and after I put it on it felt slower. The head has been milled about .015" w/Stock cam My mods are ebay header,2.25" exhaust , Short ram intake, Ign timing is stock at 16*. My best 1/8 is 10.2 at 72mph w/ 2.5 60' :bustout...

I have a stock Z6 bottomend with a PnP Z6head. I bought a Zexdry kit used for 220$ and only has the 75hp jets. I have been told by a lot of people this will be fine on my stock engine and will give me nice gains. Have also been told by many people even though Zex says it will be fine that it is...

I have a Z6 out of a 93 EX in an 88 EF9 and the vtec was engaugeing too early. I was missing real bad below 3k so I unpluged it and cleared the problem up.I know there is a TSB about this but don't remember the fix So I call honda and the whole set up is like 200$ but they sell the just the...

If anyone here lives around Brandon/Valrico Theres a car show at the Sonic in front of the big super wal-mart on SR 60 in valrico. Very few ricers come from what I have seen

I need a Dseries engine Asap. if any one in the tampa/brandon area has a D15/16 engine PM me or AIM Absu88 thx

when i was adjusting my valves today i noticed the LMAs would not move when the cyl was on the intake stroke is this right? i also did a compression test and hears how it went #1 195 psi #2 165psi (185 w/oil) #3 200psi #4 200psi. there is a ton of blowby as well, like clouds of it from the...

can i use an HF dizzy w/ Si ECU for my mpfi swap?? i have a D15b1or2 i'm getting code 9 and have no resistance at the cyl sensor wires. that means its bad right??

pick up only. i'm selling these for a friend. rebuilt B16 vtec head race port and polish w/ port matched intake. 3 angle valve job the casting # i seen on it is PR3-1 i'm not really into Bseries sorry hes asking $800 for both. 91 mitsu DOHC2.0 rebuilt w/ new SS valves $600 305 chevy heads...

ok i did the swap and now my injectors are not working. i have power to them i have fuel to them i have spark and timeing. i tested the injectors. are have 1.5-2.5 ohms. i have ground at main relay and at the ECU (A2) i can get it to start and run as long as i'm spraying ether in the TB. any...

i have eveything laid out for the swap and looking at the resistor box from an HF it has 3 extra wires. soild yellow, blue w/ yellow and soild white. i'm looking at an asian wiring diagram book and see nothing on the wires for the HF. the write ups that i have seen show nothing about them...

i'm doing a stock rebuild on a D16Z6 and was wondering if clevet 77 bearings would be ok or should i get OE ones? i am useing the 77's on my built SBC and have no problems.

i am building a Z6, nothin fancy just port and polish head and intake mani and port matching them. balanceing the stock bottom end. Bored .020 over to clean up cyl walls. i have an Ebay chrome header that is 2" on the collector. for a muffler i'm getting the flowmaster axle back. its a 2" pipe...

looking for a D16Z6 dizzy

i think this is for here since it has to do with ECUs but is kinda swap too.. anyhow i have an 88 civic DX and when i do a Z6 swap w/ a P28 ecu how do i check codes? same as i do w/ my stock ECU? sorry if this has been coverd before but haven't found any info on this

i have a 91 CRX HF guage cluster and bezel(sp) for sale. has 147456.0 i have no pics sorry. asking 30$ obo

looking for a low miles good condition D16Z6 that is close to Fla i don't want to have one shiped. I will meet halfway if you are willing to. I live in the Brandon area near Tampa. also looking for a 91 Si manual trans and R/F spindle that is also near me. Thx

when if ever you guys have shipped and engine or something of that weight. who do you go with?? i know i need a to and from addy but i just wanted an idea for a good company to go with

looking for a cheap easy swap for my 88 DX(OBD wireing i'm not worried about) I'm not looking to race or tune it extensively. i have looked at all of these over and over and can't decide on which one to go w/. I'm looking for a little more power than i have now and w/ less miles (at 200k now)...

need a Dx or Si 5speed tranny prefer newer Si