Search results for query: *

its pretty much what the title says. i'd like to buy the shift cables/linkage from a prelude or accord. I would be willing to purchase the entire assembly if need be. please let me know AIM: piccolobatman or leave me a message on here.

Ok, my check engine light used to come on, and when i checked the CEL codes it was 9*- Accord Civic CRV CRX Del Sol Odyssey Prelude 85-98** 86-98 97-98 85-91 93-97 95-98 85-98 CYP Sensor (Cylinder) defective circuit or unplugged / defective sensor * not a valid code for any throttle body...

ok, so the plan is, to use the 15x7s as wheels to hold my BFG Drag Radials. 235/60/15s if that is possible, on a facotry ride height EG hatch. is this possible? for track use of course. and which offset if my only choices are 38mm and 40mm? i'm guessing the 40? if that size wont work, can...

when wanting to switch to a belt that wont run the AC on a K20a3, what belt do i use? i ask this because my buddy's compressor bit the dust, and he can't afford to fix it yet, so we want to bypass that belt. its in an EP. thanks in advance everyone.

i need the fittings for each end of the the fuel line between the fuel filter and the fuel rail. any help here would be greatly appreciated. its for an f22 fuel rail. thanks guys remember, i need both ends if possible?

ok, so i apparently picked up an SH block unwittingly. and my intermediate shaft is from a non-SH block. i had read/heard about a plate of some sort, to allow me to use my current intermediate shaft, and current block. has anyone heard about this? here is a link to what i am talking about...

i am testing the waters for when i sell my hatch. i want to finish it, and drive it a little before i sell it. but my ideas have moved to better things. stripped, Relocated battery to rear. 97 USDM h22a w/ Type-S pistons(hand de-burred) Fidanza Flywheel ACT HD Street/Strip clutch Gator...

i dont want to lower my car at all, for larger tire clearance. but i want a stiffer spring rate because i have an h22 swap. what year(s) integra springs can i just swap into my CX hatch? thanks in advance guys and gals. also, if there is a difference in spring rate, let me know.(between the...

i have a set of b16 rods and pistons laying around. lookin to sell them if anyone needs them. i dont think the pistons are usable, i THINK the ringlands are bad. rods are fine tho. came from a USDM civic Si, when swapping to aftermarket bottom end. make offer. located in orlando FL

someone told me that the 00-01 Lude's came with OBD2B or OBD2.5 whichever people so choose to refer to it as. i'm looking for clarification on this. any help is appreciated.

firstly, i'm curious as to anyones impressions on phantom grip. thanks in advance secondly, how high can a factory h22 rev? the bottom end is what i'm concerned about mainly. i can get the valvetrain to rev to 10k with the aftermarket parts, but what does the factory bottom end hold up to...

i'm doin this to see how many people would be intrested in buying an intake from jeff at import builders. i have been in contact with him and he asked me to see if anyone was intrested. group buy would be great, i think he wants to try and move atleast 20 of em. per our conversation "What I...

It's in North Carolina. www.tailofthedragon.com there is a group of people from www.jdmuniverse.com attending this, actually, i am pretty sure its being setup by one of the admins. looks like a lot of fun. if anyone is intrested in more info, register on jdmuniverse, and scope this link...

i apologize if this is in the wrong section, it isn't really a tech post, but more a request for help. this whole Euro-R manifold was a great idea, until i had to start working on it. anyone have any good tips? or somewhere i can go to get mine the way it should be to be on the h22 in the EG...

i was curious. i remember a moderator on the board that also ran/was involved with nissantech. or atleast had a vast knowledge of nissans. perhaps nissan ninja can help me i've slacked on my nissan knowledge and i need help. someone please reply here or pm me.

i might be gettin a free engine. and i'm so happy. 98 H22a -darton sleeved -8.5:1 forged crower bottom end (rods, pistons, rod bolts, rings) -entire top end with reworked valvetrain(not cams tho) -accesories i happen to have a spare h22 tranny layin around as a back up incase i blow up the...

ok, i realize to unlock the potential of my engine, i need to upgrade the springs and what not, but for the sake of arguement....just answer this question withou consideration to the other issues. Which camshaft is the best for my h22? i have a full intake system, Euro-R intake mani, Type-S...

i'm lookin for intagra leather interior. perferably black. front and rear.

just to let everyone know, hurricaines suck ass. i know i probably spelled it wrong, but you get the idea. some retarded number of ppl are without homes and even more without power. yay! sarcasm. sorry, i hate no power. gr.

i have aquired a CF hood for a 95-2002 cavalier. if anyone is intrested let me know.