Search results for query: *

Well I have begun my wire tuck and plan on posting up some pics along the way. Alot more will come later, the easy part is getting everything taken out. I am going to move the fuse box under the dash and the battery to the trunk. I took out the heater core and the blower motor, so...

Can anyone give me a part number for yellow and pink rod bearings for a b18b (LS)? thanks ahead of time

I just got my block back and a few misc. parts so now its time to put it all together again. Maybe this should be in multimedia? But I plan on doing maybe a little writeup of the build process to help provide a little info. Build list: HEAD PR3 casting JUN III cams Golden Eagle cam gears...

Alright, my VSS just took a crap on me and I am not sure which one or where to order. The transmission if from a 97 ctr. Its an lsd. I thought that one from a 99 SI might work but its not the same. One from an integra perhaps?

I swapped out the brake booster and master cylinder from my 97 ex for a 97 civic type R. It was actually pretty easy, I had to make up one new line for the master cylinder. The outlet is on the opposite side because of the whole RHD thing. on the right is the ex left is ctr now its...

The conversion was pretty easy, only taking a few hours. The biggest pain was the e-brake cables by far. I snapped a few pics along the way and here they are.....

Complete 1997 d16y8 motor 65k $450 0b0 excellent running condition when I pulled it. 97 ex transmission $200 obo Used type r rocker assembly $150 obo very little wear on contact patches B&M short throw shifter, double bend steel, new $25 obo Used stock type r clutch. good condition $40 obo...

Alright, I just put my build in with a clutchmasters stage 3 clutch. I had the b16b swap int my car last year. So I know the tranny is good, my problem is that it is almost impossible to shift into first when I am stopped and the car is running, but when it is off its no problem. Going down...

I finally got everything together and am ready to put my engine back in my car, and do some tuning. I'll try and post some pics. It feels so good to finally finish a build. Now its time to deal with the inevitable bugs. List of what I've been up to: b16b block gsr crank balanced and...

Quick question, when reading the numbers for the pinouts you hold the plugs with the pins facing you, and the wires leading back to the car correct? Thanks

My buddy swapped a first gen b16 with a pr3 ecu into his teg and he wired in his vtec, but he says there is no vtec. I have yet to go and take a look at it. So if anyone has done this swap before, what do you need to run for vtec on this setup, (vtec solenoid, oil pressure switch, etc.) what...

Well I finally have it put together, or will when I get my con-rod bearing deal straightened out.

I ordered my main and rod bearings from an acura dealership in FLA, the mains were fine. But the rod bearings look like they are all tarnished. Also when I compare them to a set that I had around they are not as wide. The package also said p-72 not pr-3. I don't believe that this makes a...

Port and polish, 3 angle valve job, bronze valve guides, titanium retainers and portflow outers, type r inners.

Probe 7.1cc dome. CR around 12.3:1 81.5mm JUNIII cams

The local honda dealer in Lebanon NH, were i'm from eats ass. Waaaayyy overpriced. I had put my stock engine back in my ek and needed new ball joints, so I had them do it. The price on the ball joints wasn't bad. But because one of them was fucked I couldn't get it off and couldn't get the...

Just a quick thanks to IB. I got my rods and pistons today. I took a pic of the rods, but not of the pistons. I was in a hurry to get them to the machine shop so they could bore my clyinders and match the pistons to each one. Gsr ultralight I-beam rods Probe 81.5mm 7.1cc dome pistons

Obd2a PCT type r ECU. Was in excellent working condition. I am converting to obd1 so I don't need it anymore. I am looking to get 225 obo.

My car is a 97 ex coupe, I am going to be running hondata on my ctr. I know that you cannot run hondata on obd2. I will be using rc 440 injectors. Can I use my pct ecu or do I need to get an obd1 ecu and use a harness jumper? As you can see I am a little confused, so my basic question is...

So driving around today my automatic transmission starts acting up in my Landcruiser. It keeps getting worse, it won't shift out of 1st and now reverse does not work. I am ready to have a bonfire right about now, couple cans of gas, a propane tank and a .22. Well maybe not, I have to check...