Search results for query: *

Ok Heres The Deal. I Have A 1988 CRX HF Shell That I Picked Up. So I Put My B16A2 From My Other 91 HF In It And Harness Engine/Underdash, Its Converted To OBD1 With A Chipped P28 ECU With A B16 Base Map. I Got everything In And Started It Up "Code Free" So I Took It For A Drive It, It Runs...

Ok Heres The Deal. I Have A 1988 CRX HF Shell That I Picked Up. So I Put My B16A2 From My Other 91 HF In It And Harness Engine/Underdash, Its Converted To OBD1 With A Chipped P28 ECU With A B16 Base Map. I Got everything In And Started It Up "Code Free" So I Took It For A Drive It, It Runs...

I have a 1988 CRX HF with a b16 converted to obd1, the wiring harness is uncut. I got some new spark plugs went home and put them in then adjusted my TPS Sensor because it was out of spec' then started it up to go test drive it, and it immediately threw a code 3 "MAP". Ive changed the sensor...

I Got A B16 In A CRX HF Converted To OBD1 Via Ry-wire I Bought Some NGK-R Plugs, Drove Home Put Em In, And Adjusted My TPS Sensor In Spec Because 'It Was Out, Then I Started My Car And Immediately Threw A Code 3 "MAP" I Replaced the Sensor 3 Diff. Times Reset My ECU And Still A Code 3. So I...

I:m Fed Up With My Rex Idk Wat Else To Do. Im Getting Fuel, Spark But It Wont Fire, Just Cranks And Cranks, The Main Relay Is Good, Distributor Is Good, ECU Is Good, All Grounds Are Good And I Added Grounds, Fuel Resistor Is Good I Have Plenty Of Gas In The Tank, Spark Plugs/Wires Are Good. Its...

Ok i just picked up a 88 hf shell, its converted to obd1 and is already wire tucked, i put in my obd1 b16, its got obd0 injectors, here my problem. my car wont run, it has spark and fuel to the rial but the injectors wont spray, ive checks all gorunds, added some, switched main relays, ect. ive...

Got A 88 CRX HF With A B16A2 Converted To OBD1, My Car Wont Start, I Have Spark, Fuel Pumps New, Getting Fuel To The Rail, But Injectors Wont Click On So There For No Fuel To Motor, I Turned My Key On #2 And I Put The Voltage Meter To Each Of The Injector Clips And Im Getting 12v All The Way Accros

Ok got a 91 Civic Si, It has a 2000 spec JDM ITR motor, with the badass JDM header, It got a Rs*R Exmag catback with a Blox testpipe, its converted to obd1 with a chipped p28, its got a base map for type-r considering its a stock motor, im going to run it at the track next week, so im gutting...

Ok im getting an EG hatch, i want to either build a B-Series or H-Series For Boost, What would be the best bang for my buck i want like 500 whp, i had a turbo d but it was only like 300whp, i just got a settlement and want to build something, just need some opinions guys

ok i have a crx converted to obd1 with a b17a1 da GSR, and a matching p61. ever since ive had the swap and ecu, my cars been throwing code 41. oxygen heater and ive tryed new o2 sensors, so i tested the o2 wires and its getting little to no voltage coming out of the ecu, so i took the cover off...

Just picked up a 94' si for dirt cheap, the head was done, so i have a y8 head in my garage. i put it on and im running into timing issues. Z6 block with Y8 head, and im using y8 cam gear with z6 belt and its not working so ive search and heard you have to use - y8 cam gear w/ y8 timing belt...

Just picked up a 94' si for dirt cheap, the head was done, so i have a y8 head in my garage. i put it on and im running into timing issues. Z6 block with Y8 head, and im using y8 cam gear with z6 belt and its not working so ive search and heard you have to use: - y8 cam gear w/ y8 timing belt...

ive heard about putting power windows in a eg hatch, i want to do this, i know you can use ex switches but what about window regulators can i use ex ones or what

I just got a deal on a eagle stroker kit for a b16 (1.6L to 2.0L) with high compression pistons and knife edged crank, it will be going in a jdm b16a block with type-r oil pump/ water pump ect. the head is a jdm b16 head with ctr internals, buddyclub cam gears, skunk 2 intake mani/ with blox tb...

1994 CX Hatchback - Stock K20z1 (210hp) - Hybrid Racing Fuel Rail Mated To Aeromotive Regulator - Stage 2 Exedy Clutch (Solid Disk) w/ 12lb Flywheel - Aem Intake w/ Filter - K-Pro ECU What Do You Think I Will Run With 93oct. On Slicks Does Anyone Else Have A Similar Set Up That Can Tell Me...

I have a jdm b16a comverted to obd 1 with a p30 ecu. its a good running motor but once in a while it has a bogging problem. when i press on the gas its like its holding back and hesitating. but it only does it sometimes. its throwing a code 20(ELD) and thats it. any ideas? Thanks!

Alright When Push The Brake Pedal Down My Brake Lights Dont Come On, But When I Turn My Running Lights On The Brake Light Stay Lit With Them, I Checked Fuses Grounds No Luck? So If Anyone Has And Ideas In What The Prob Is OR Suggest What Exact Grounds To Check It Will Be Appreciated?

Are D15B7 And D16Z6 Crank Pulleys The Same? Can I Put A B7 Pulley On My Z6 With Out Timing Issues?

i have a b16a2 and i want to put ITR cams in. do i have to adjust the valves, if so can someone tell me the specs

i have a b16a2 and i want to put ITR cams in. do i have to adjust the valves, if so can someone tell me the specs