Search results for query: *

Tell me about them? Anybody have them installed? Maybe a better pump for the price? Im planning on making about 300whp to max of 350 with a high comp (13:1) with a 100 wet shot of nitrous. I had a 255 but it died while my car has been sitting for the last year and maybe down the line looking...

Oh well the other high comp engine is a little bit smokey and has lost some power......still not bad for a cheap low budget build. in all do reality, the engine can still pull the teg to a low to mid 14 sec 1/4 mile. This time around its going higher compression, the most aggressive LS cam...

I have a p75 head that was ported and polished by JG engine dynamics with oversized 31.5 millimeter intake valve and 28 .5 exhaust valves. So my question is I'm going to have to replace the valve guides on this head and might have to replace the valve seat. So if I have to replace the valve...

Im going to have my friend paint my car(finally) and I need some advice on paint. Im on a budget but I want a nice finish. I found DuPont paint Championship white for $250 a gal for base and $150 for two quarts clear. Is there better paint for the price? Or should I stick with DuPont...

As the title says my orthopedic surgeon informed me that I need to have back surgery to fix my problem. So what is my problem? (insert sigh) I herniated two discs in my lower back on september first while stocking automotive lead acid/AMG batteries at work, the worst one being L5-S1. I...

Need ASAP Cash In hand PM me

So my GF just bought a 95 Eclipse and it has weird tranny issues. some times it runs fine with no problems but then it just kicks into limp mode (stuck in 2nd gear). I changed the fluid and filter, swapped shift noid, and input/output speed sensors. same thing keeps happening. Also it only...

Well my new buiild eats oil.....lots of oil! takes about 1qt every 300 miles and the oil goes black within 500 miles. Fresh rebuild 82mm LS block with 11.5:1 comp ratio BC 403 cams, JG LS head. Compression test is 230 225 220 and 225 all good, Also notice my copper plugs being fouled by brown...

Who's going? I know we have a few guys here from cali.

computer crashed and the hard drive was at fault. long story short I bought a new hard drive and need the recovery disk. if anybody has it or knows were to get one CHEAP please let me know. PM me links with any help. :ph34r: Thanks

YouTube - 2.1L 400HP / 300TQ Nitrous CR-X Never seen numbers like that on high comp and nitrous. :o

JG 1001 Cams, Simple bolt on can use stock springs with stock rev limit. Stock idle Works with all B series non vtec. B18a B18b B20b B20z. Camshaft Specs lift in/ex: 410/410 dur in/ex: 260/260 valve lash in/ex: .007/.009 works for all motor/ nitrous / turbo. $150 shipped FIRM

well im trying to keep this as simple as possible, I now have a socketed P28 but I need a socketed nonvtec ecu for my new build. So What Im asking is....Can I make a Vtec ecu to a nonvtec ecu?? I know you can make a nonvtec to vtec but can it be done the otherway arround? I really dont want...

well Im breeding some roaches for my girls bearded dragons, here is a small clip of my colony. YouTube - roaches If anybody else has med sized lizards and feeding crickets, well you need to switch over to roaches, they dont smell and breed super fast!

So I dropped my Crower 403 intake cam, What should I do now? I hear they break when running when you drop em. was gonna clean and coat them with wd40 so I took them outside, box tore on the side and spilled my intake cam on the cement. :( looked at it close and It looks like nothng happened...

Looking for OBD1 engine and under dash harness, OBD1 alternator, OBD1 LS dizzy, OBD1 PR4 or P75 ECU and OBD1 stock injectors. trying to get a buddys car BAR'ed ASAP! Be nice on the price as he is a full time state student with a full time job. Needs his car running asap! :)

My roommate has a 93 accord and its acting really weird. First of all the fuel pump went bad, so we changed that. Next the main relay went bad....resoldered and fixed it. now the car sputters lags and runs like shit 9/10 times. when we first start to drive it runs smooth, after about 5 min...

Well here is my teg, jdm b16a with bored LS TB, Skunk 2 IM, RC 310cc injectors, E-bay type r replica header, 2.5 all the way out. Pretty nice.....But Im getting 20 MPG! so Im getting It tuned this week. http://www.youtube.com/watch?v=wN60CcMG2RM

I was driving down the road and I hear a loud thump....shit I lost my intake filter. NO I lost the bolts that bolt from the mount to the tranny. So now I need to fix it and dont know how. :( Heres some pics.

http://www.youtube.com/watch?v=0cwVeIVZY18&feature=pyv&ad=3614555634&kw=feeding&gclid=CIWM46jQvp4CFSWlagodUC5log