Search results

  1. H

    question about turbos

    hey guys im new to turbos and dont know a whole lot about them. a buddy of mine works at mazda and has a couple t3/t4 turbos from a mazda speed 6. are all t3/t4 turbos the same externally?( im sure internals are different from other t3/t4) but what i was wanting to know is if i were to buy a...
  2. H

    tunners in alberta???

    hey guys i live in red deer alberta. im looking for a good tuner in red deer or edmonton or calgary to tune my integra. ive heard tech motion in calgary is good but just looking for more options. thx
  3. H

    edlebrock turbo kit?

    hey guys,i have a 97 integra with a b18b1. ive built the motor a bit and now want to put a turbo on it. i found edelbrock has a turbo kit but they say its for a gsr. i was wondering if i were to buy this kit and just use the stock intake mani/pick up a different ls intake. would this be a good...
  4. H

    b18b1 hard starting cold

    hey guys i have a 97 teggy i swapped in a re-built b18b1 about 4 months ago.last month i started having trouble starting after the car sits over night or all day at work. it cranks really good,but it will spit and sputter until i open the throttle,then it will fire up but it will stall out...
  5. H

    intermittent loss of oil pressure???

    hey guy,i have a 97 integra rs. i just installed a new motor last weekend. its another b18b1 but it has eagle rods,acl bearings,srp pistons, head pnp. oversize valve,crane turbo cams. during first start up it was fine,no problems,drove it to work the next day and re-set valve lash,then drove...
  6. H

    transmission upgrades???

    hey guys, im in the middle of building a turbo ls/vtec and am putting a itr transmission in the car, is the trans going to be strong enough to handle the power out put? i know ill need a good clutch,just wondering about the gears/syncros?? any help would be great.thx
  7. H

    titanium vs steel retainers

    hey guys, im currently building a turbo ls/vtec fo my dc integra.i plan on using compcams 57200 cams(RPM range: 2,400 to 8,600 rpm Duration at .050" lift: 230/240 (int/exh) ). this car will be a summer daily drive/weekend racer. now im told by alot of ppl to use titanium valve retainers. my...
  8. H

    b18a/b18b conversion???

    hey guys ive searched and searched but cannot find any real answers, i have a 97 integra rs. i want to build a ls/vtec for it and was given a b18a1 block(bare block only). will all the sensors and brackets ect..... from the b18b1 in the car now fit onto the b18a1? or should i be looking for a...
  9. H

    swap info needed,please help

    hey guys imstill new to the honda scene, but i have a 97 integra ls that i wanna build a ls/vtec for,now i got a b18a1 block from a buddy for free however its just a bare block. my question is will all the sensors and brackets and accesories from the b18b thats in my car now bolt right up to the...
  10. H

    ls/vtec stroker???

    hey guys im building a ls/vtec for my 97 integra ls,it will consist of a b18a block and a 97 gsr head. i was thinking about stroking it out to a 2.0L using a eagle rod kit, however i have had some ppl tell me that by stroking it i will blow the motor if i rev it to 9000 rpms. i am just looking...
  11. H

    clusters

    hey guys i have a 97 integra ls,i am building a ls vtec for it. i was wondering if the cluster from a gsr would connect to the ls's wireing harness so i dont need a after market tach so can keep the interior as stock looking as possible. any help is appreciated
  12. H

    vtec controller

    hey guys im in th middle of building a ls vtec, and i heard someone say that instead of using a vtec ecu a vtec controller canbe used instead,i am just wondering if its true or not? or if its still recommended to used the ecu for the head(i have a 97 gsr head)
  13. H

    ls/vtec vs ls turbo??? help please

    hello everyone, i have a 97 integra ls, i was able to get a b18a1 block fo free from a buddy( im told the b18a and b18b blocks are the same) i wanted to do a ls vtec build and maybe turbo it in the future, but i cant find a gsr head thats not ridiculously over priced. now i am wondering if i...
  14. H

    average 1/4 mile times

    hey guys. i bought a 1997 integra, ls non vtec. i ran it at the drag strip last night and the best time i could get was 17.6 seconds.(1/4 mile) i have a aem air intake and cat back exhaust, otherwise stock. anyone else run a fairly stock integra ? i was expectng to run alot fast, just wondering...
  15. H

    b18a swap

    hey guys im pretty new to the honda scene. i have a 97 integra ls. im wanting to build a ls/vtec turbo to drop into my car. i found a b18a motor i can get for free, so im asking if the b18a motor will drop right into my 97 with a b18b? how much work would it be and is it worth while or should i...
  16. H

    condensation problem

    hey guys i have a 97 integra,when i bought it there were some euro style tail lights already installed on it,and recently i have noticed alot of water condensation on the inside of the lenses,is there a way to re-seal them or should i be looking for new light? thx for the help.
  17. H

    ls all motor build

    hey guys,i got a 97 teg, ls,so no vtec. and and looking at intake manifolds, and am looking into the skunk2 pro series and the edelbrock performer x. just wondering if anyone has used either of these before and which one would be best to go with,any help would be great
  18. H

    need advise

    im still new to hondas and im wanting to do a ls/vtec conversion on my 1997 integra. im looking into using a gsr head,im thinking about upgrading cams tho,i hear skunk stage 2 cams are a good investment. im wondering if i were to use these cams with a stock ls bottom end would i run into any...
  19. H

    adding vtec??

    i have a 97 integra non vtec 1.8L. i am looking for any info/advise/tip i can get about instaled a vtec head and how much work is involved. or if it is more worth while to find a vtec engine and just sway them out??
  20. H

    vtec head swap?

    i have a 97 integra non vtec.i am looking into putting a vtec head on. i an wondering just how much work is involved with the swap,or is it more worth while to swap the motor,and if so which motor would be the best bang for my buck?? p.s would prefer to keep it n/a rather than turbo.
  21. Try your Search on Google

Back
Top