Search results for query: *

Stock b16a with a hondata ecu. Warbro 255 pump. Misses when in vtec. Turn vtec up high enough to not engage and runs up to 7k no miss. Had this issue before and adjusted dead times to fix. Log shows running lean and voltage drops to about 10 amp when on vtec. Right now leaning towards toasted...

To catch up those who dont recognize me. B16. Odb0 with an obd1 dizzy and ecu. Was running crome and had the miss. Was only under vtec then under non vtec. Bought new ecu with s300. Loaded base p30. Still have the miss. New plugs and wires. Sprayed carb clean all over and cant detect a leak...

so according to my RD-1 my TPS was going bad as the voltage jumped when I tapped the tps. I got a new TPS and when I went to calibrate it, it stays at 1.5. I unplugged it. 1.5. what ever I do, 1.5. heeeeeelp oh.. obd1 crome almost stock tune. only eliminating ELD Odie

so everything is going ok except when I push in the clutch while driving, it idles about 1800 to 2200. then I "Blip" the throttle, all is well. (~800 rpm) Throttle cable isnt sticking as the TPS voltage shows it is at "closed" position for the Throttle. Happens warm or cold. it doesnt hunt...

Without writing a book, here is the skinny. Jdm b16 stock with header. Bought 8 years ago ran sweet. Swapped into a fiat x19 and finally got it done last year. Spun bearing before I could run it into vtec. NOTE: if engine sits for 7 years, prelube like it was a new build. Replaced with other...

Doing a head gasket job and messed up the alignment dowels . Does anyone know the size or where I can get them? All I see online searching is for the ls/vtec. If I go to Honda, will the 96 del sol with b16 work on a jdm (pr3) head? As you know, they are only "this car, this part" people Odie

hi, its your semi friendly pain the arse fiat x19 B16 guy. got another question that I dont know if any one here has run into . I am putting a fuel cel up in my frunk (front truck) I have the external walbro fuel pump currently. What I am looking for is help on figuring out how to run it. I am...

Probably an easy question, but I googled and I couldn't find the answer. Because the engine is going into a different car, I used the starter circuit of the fiat. Not a problem. Starts, but instated thinking, is this pinout to tell the ecu the car is in start mode? Should I branch off the fiat...

hopefully easy question. still fighting the over heating issue, but I have the stuff for the head gasket replacement I am doing after vacation. Can a sensor fail and give the wrong signal? let me explain. from what I can see on the all knowing google world, when a temperature sensor fails, it...

So I need your guys opinion. Latest on the X19 b16 is we have a warped/cracked head or a blown head gasket.I am going to leak down test it to verify, but it is really pointing to that being a big cause of not being able to keep the engine cool. If this is true, I have a few options. Wondering...

I put the K-tuned upper coolant neck on the b16 to aid in filling the cooling system (remember this is in a fiat X19). the issue I have is the stock one it replaced has a coolant tube going to the throttlebody/ intake. the K tuned does not have provisions for it. Anybody want to guess where I...

so here is the issue, then I will explain. I dont think I am getting any circulation. I know I am not getting enough to push the coolant through the radiator as the hoses are cold and I shut off the engine at 200. Info needed for diagnoses; radiator is not plugged, that validated with a...

Got to drive my fiat x19 with the b series finally. Thanks everyone for their help. Now I have another question. Is it possible to adjust the cam positioning with the front covers on? Here is the issue. After putting the motor in we discovered the previous owner of the engine was off a tooth...

I have a Y1 transmission. will the same driveshafts/mid shaft fit I swap to a later transmission (thinking hydraulic LSD) Odie

Ok, I am ALMOST done with my 7+ year b16 into a fiat x19 project when I discovered a slight rod knock. So I am in need of opinions. Here is a little history. I bought a jdm b16 (second Gen obd1) without hearing it run, was "told" it ran fine. BecauseI just needed it as a "mule" to block out...

I have a Y1 transmission that I have hooked up to my b16 fiat x1/9 swap. I am running the Fiat shifter because trying to use the honda shifter to go mid engine was being a pain trying to route both rods around the fiat's stuff going back to the trans. I finally got the rod/shifter positioned in...

Trying to get the driveshaft into the midshaft. I get the splines lines up and it goes in but doesnt look like all the way. Help! Odie b16 fiat x19

I have a JDM obd0 b16a converted to obd1. with a y1 non lsd tranny. it came with a mechanical speedo. The car i put it into needs the electronic speed sensor. I am not using the stock dash from any honda/acura but a custom LCD. Can I swap an electronic speed sensor form another tranny in...

So I have this lovely swap I have been working on FOREVER. we are now down to this. Timing we believe is off. We have lined up the cams with the proper arrows and checked it against the keyway on the cam. now on to the crank pulley after looking for what seemed like days, we finally found the...

trying to troubleshoot a no start situation. I have a rywire race harness (open ends, not plugged into car wiring because the car isnt a honda) I am starting to run down the harness thinking I dont have the leads connected to the right places. Already used what rywire sent and it still wont...