Search results for query: *

Sold the ECU, sorry. I have a fuel injector resistor box for the DPFI to MPFI conversion. Sold. Also a brand new BBK throttle body, never been used in original box. It fits any 92-97 civic including the 2nd gen ZC's. Would like $175 shipped. And I have a '89 Integra Distributor with cap and...

I have a brand new BBK 62mm throttle body in the original box that I would like to sell. It is brand new and has never been installed. It is for 92-97 Civics. I'm asking $225 shipped or e-mail me with an offer.

It is a 1988 Civic LX. It's got 155,000 miles on it. But pretty much everything that's able to be replaced is new. The engine is a JDM DOHC ZC, the engine only has been run for a couple hours total since I put it in. It's not running right now, I seem to be having some distributor problems. I...

I have a BBK Power Plus series Throttle Body. It's brand new in box, 62 mm, for any 92-97 Civic. Asking $250 shipped for it. Here's a picture, email if you want more.

I have a JDM ZC and I bought the L3 with the limited slip differential and I was told that I need to buy the clutch for an '88 CRX Si and it should fit. Well, I got a Neuspeed N2 clutch for the '88 CRX and, guess what, it doesn't fit. So is the L3 with the LSD have a different shaft size...

I am doing a DOHC swap into my '88 civic LX, and I am wondering what I have to do with the cam angle sensor that is on the exhaust cam. Is there any specail wiring that I may have to do or do you just not hook it up or what. Any advice would be appreciated. Thanks

Hey everyone, I'm building up a ZC and I was putting my head on tonight, I put the cams in and then I was putting in the camshaft holder bolts. The things that hold the cams in the head, anyway, I seemed to have torqued them down to hard and two of them snapped. I was just wondering if anybody...

I have a ZC that I have a fully built bottom end, I haven't done anything to the head yet except for a port and polish. I plan on getting the HKS camshafts but I was wondering if anybody makes valves, springs, retainers or anything fof the ZC, and if not is there something that I can borrow from...

I am installing a fully built ZC that I am just about finished with, I have the L3 LSD tranny with a Neuspeed clutch, and I was wondering about the best recommended break in process for the new engine and tranny. Also is there a specific oil I should use, a brand that is better than the others...

I am looking for an after market throttle body for my ZC, the intake manifold is the same as the 88-91 CRX Si so I have been looking for one for that car but I can't seem to find anybody who makes throttle bodis for the CRX. If anybody knows of a website the sells them or a brand that makes...

I have a JDM ZC and I bought the L3 LSD tranny to go with the engine. They will be going into my '88 Civic LX, I was wondering if I will need new half shafts or anything like that? I was told that I might need 89 Integra axles but I don't really know. Thanks for the help.

I have an '87 JDM ZC engine that's going in an '88 Civic, I am donig a full rebuild of this engine and I bought some Eagle H-beam rods, part #CRS5394H3D, these are for the ZC, or so I was told, and I put them in and tightened one down on the crank, but when I tried to rotate the crank the rod...

I have a block with some rust inside so I am going to bore it a little. My machinist says that if I can get pistons that are 10 over it should be fine. Does anybody know somebody on the internet that sells over sized pistons for the D16Z6. What brand and what site? Also what would be the exact...

I have a JDM ZC and I'm replacing the rods and pistons and the such and I obviously need to replace the rod bearings, but I'm unclear on how to tell what bearings I need. I'm pretty sure that I need bearings from the D16Z6 but I talked to a guy at a Honda dealership and he said that there is...

I am looking for some ARP head studs for my ZC. What do I need? I assume that I can just get some for an '89 integra, but where can I find them? If anybody has some for the ZC could you let me know where you got them, or an internet site that sells the ones that fit the ZC. The only ones that...

I have a JDM ZC and I am doing some pretty major renovations, such as new pistons, rods, rings, and the like, also while I have the engine torn apart I was thinking about getting the head ported and polished. It's pretty expensive but I want to know if it would be worth the money to do it or...

Does anybody know if any of the pulley kits from AEM will work with the JDM ZC? I was looking at the kit for the 88-91 CRX, #AEM-23-7009C. If this one fits please let me know, if not is there a kit out there that would fit. And what brand. Thanks

I just got my ZC engine and I am starting to take it apart and build it up. I need a new throttle body and distributor. What throttle body should I get, I'm going to get a large aftermarket one, since I have to replace it anyway. I can just buy one for the 88-91 CRX Si right? What else should I...

I'm just recently purchased a JDM ZC for my '88 civic and I bought some Eagle rods and some SRP forged pistons and rings to go with. What else am I going to have to do to allow the bottom end to handle some horsepower? I am building up this engine to handle a 75 shot of n20 and about every bolt...

I just recently bought a JDM ZC and I was wondering what kind of parts from the D-series will fit. I want to get larger throttle body and fuel rail and regulator among other things. Can I just buy parts for the D16 or is everything going to be mix and match? Also, does anybody know where I can...