Recent content by zootel

I have the OEM Fenders for this car but I wanted a diff look. I have the side skirts and rear bumper that goes with the front bumber but I just havn't been able to get them on yet. My motor has over 300K miles on it so I guess a head swap would be a bad idea. I am in the process of buying the...

I have a 1990 CRX HF with the D15B6 or 1.5l with a manuel Transmission and i am trying to get more out of this car. There is not a lot of selection around my area as far as parts.I am thinking on trying to chip the ECU. I already have installed the following: cold air intake (2.5 inch) ss...

ommon semi's use what is called a rig saver. if they over ramp rpm it triggers a spring loaded plate that slams closed cutting off all air into the intake system thus shutting down the engine. We have them on the truvks I drive at work (I work for Halliburton, for those that don't know what...

Well I was looking at it today and noticed that it had just a little play in the center shaft, So I decided to take it apart and see if I could do anything to tighten it up. Well in the process I seem to have snapped the tip of the shaft off on the outer air side. I think it is trash now. or...

This is off of like a ford turbo disel pickup not a semi. and I bought it for 35 bucks. used in good shape.... the guy got it from an estate auction and it was in a box that he bought for like 5 bucks. you can go to the link at the bottom to see pics of it. I am also building my own manifold for...

I have bought a turbo off of a turbo disel pick up to try and see if i can get it to work on my crx. any suggestions would help.

I have a new problem. I think I have found out why my crx is such a terd. During my routine engine inspection / checkup I noticed that I have white tipped spark plugs. I asked my brother in-law about this and he told me that it means that my fuel system is running lean. I just am not sure how to...

Can some one point me to the info about swapping an h22 into a 90 CRX. I know that I need a mount kit, wiring harness, and the ecu. I just wana make sure that is all I will need, or to see what else I will need. I apologise if this topic has been played out but I couldn't seem to find a...

I have a 1990 Honda CRX HF with the D15B6 engine. I have installed a cold air intake, NGK V groove plugs, 10 mm wires, a stainless steel header with 2.5 exhaust, all of the way back to a N1 titanium turbo muffler. My question is do you guys think it would make a big difference with an electric...

How good is a mini me?

I was wondering how a D15B6 would run with the top end off of a D16Y8.

ok I think I have her talked into letting me fix up this crx the way I want to. I am buying this Accord with the F22A1 motor, I plan on swaping from the subframe up, but my question is what parts would I need that would not be on the accord? eg, Axles, Linkage, or Spedo cable....... I just...

Well my wife had decided for me that I was not going to put any more money into my crx. So I guess here are my finished pics with the exception that I just put my hood back on after I took these pics. IM001095.JPGIM0IM001097.JPG01096.JPG

Ok I went and looked at the engine in the accord better and it is a F22A1. I also parked my crx next to the accord and compared the motors; I came to the conclusion that there is no way I want to get myself into the trouble (the F22A1 is like almost twice the size of the D15B6). I then went to a...

I have just been having problems finding honda parts near here, (I had to special order a distributor cap , rotor, plug wires, and plugs for this D15B6 the last time i gave it a tune up). My ideal Motor for this car would be a non-Vtec DOHC, but i just don't know what model of car to look for...