Search results

  1. E

    H series engine mount kits?

    http://www.enjoracing.com/engine_mounts_swap.html enjo racing has a set Call em up! Matt
  2. E

    Turbo a HF

    wreckers
  3. E

    Failed emissions test

    no, but i just had a holley high flow installed as my old pump failed
  4. E

    Failed emissions test

    Ontario, Canada
  5. E

    Failed emissions test

    I took in my b16 ef to get e-tested and it failed, miserably. the test was a 2 speed idle(too low to get on the dyno) and iut was tested under hot rod specs since it doesn't reatin the stock block. If you can help that would be appreciated... test results: IDLE hc ppm--limit-300...
  6. E

    $700, what to do

    i reccomend you save your money for something better zc,b16 or b18
  7. E

    resistor?

    what resistance does the knock sensor have? i need to bypass my knock sensor and don't want to chip the ecu -Matt
  8. E

    H22

    b16a or b18c® head
  9. E

    Knock sensor wiring

    thurr is 2 wires coming from the sensor... where do they both go?
  10. E

    Knock sensor wiring

    have done a b16A 1st gen PR3 ECU mod on my civic. Need help knowing how(where) to wire the knock sensor. The schematics that I have do not show the sensor. The wiring pinout calls for pin B19. I am told it is a shielded wire as well. Do I connect the one leg of the sensor to B19 and the other...
  11. E

    radiator hose

    i used 2 lower civic hoses. you have to strech them over the b16 nipple as they are larger dia. the top i held the lower one up to and trimmed to fit perfectly. then streched it over i did this mostly because i had a parts car with a extra rad hose
  12. E

    B-series motor mounts

    I am using enjo. just like place racing but cheaper they are stiff... rearview shakes at cold idle
  13. E

    B16 to STD help needed

    i have the shift linkage working... the reson i thought it would shift gears is that the stabilizer would be bolted to the undercarriuage and it wouldn'ty move with the engine like stock... the only prob with this is that when i floor it the shifter moves a little bit... which isn't that bad...
  14. E

    just double checking everything

    EF auto-manual swap that will cover you on the conversion from automatic to manual transmission and you will need to mpfi aswell MPFI conversion and jus to make sure you have everything... ZC swap shopping list
  15. E

    B16 to STD help needed

    hmmm... i could.... what would happen if i cut off the stabilizer and bolted it to the body of the car? i was told it was ok because i have enjo(racing) mounts and it wouldn't change gear when i accelerate because the mounts were too stiff and the engine wouldn't move enuf to shift... i think...
  16. E

    B16 to STD help needed

    well thanks guys for all your help my engine is now running i just have to find out something for a shift linkage... the local shop wants $400 for a hasport shift linkage...(cdn) so once i fig that out i will be running thanks for the wiring help, i had every wire right -Matt
  17. E

    vss question

    my cable is tit3 tho with the rear engine side mount if you wanted to dent it a little bit if its not installed
  18. E

    just got a car

    if its truely a STD you will need brakes off a dx,si,JDM SIR(what i have) or a 90-91 integra
  19. E

    vss question

    ya sho... thats what y0u have t0 d0
  20. E

    Need a little bit of help

    ok... can i modify it to work? whats the reason it will not work? that sounds like it could be expensive to get lol
  21. Try your Search on Google

Back
Top