So I have read all I can find on type r cams and I am looking for a set of OEM cams. After research....I want the CTR's for the intake but I haven't found any in the last 3-4 weeks. I found some new 00/01 ITR cams and (from some readings) the Intake on that ITR year is the same as the...
Its been raining cats and dogs since I got off work. The code 7 (TPS) came off and I got home. Went inside thinking I needed to worry about it tomorrow when I can put it in the garage. But I was still frustrated so I went out for a smoke and I popped the hood. TPS was loose as a whore. I bought...
So I have a B16A and I have decided my next project will be cams. I want some more bounce to the ounce. Sadly, as most of us know, you usually can't just get cams (unless you do stage one or stay below 8K rev'ing). You need the adjustable cam gears, springs/retainers, chipped ECU and a dyno tune...
This afternoon (and most of the evening lol) I installed a B16A3 Intake Manifold, Purge Solenoid, a USDM TB that has a place for the MAP on the top (My JDM was on the firewall) and a USDM 5-speed P30 ECU. I switched these parts with the JDM B16A parts I had on my 92 Si swap.
I have a question...
I got a used B16A3 IM so I can attempt to BAR my car. I have a JDM B16A in it right now.
The IM I bought it dirty and you can tell they took a flat head screwdriver to it in order to take the gasket off.
I want to clean it. It came off a blown B16 and has shavings from the block in it plus...
I put a B16 in my hatch back in the spring time of 09. I just started having a problem trying to re-start it.
A scenario would be going to the store for gas and when I try to start the car to leave....
it starts up and rev's to about 2K when it fires over (which is normal) but when it falls to...
Just wondering b/c a girl I know has a '03 Civic EX coupe with 7 spoke 99-00 Si wheels but she said she bought it brand new. Didn't think they were the stock wheels but I could be wrong.
So I found a 2000 B20B motor online for $350 (60K miles)
LS intake manifold
Some 'stage 1 clutch'
Some B series Header
No dizzy
My question is that I wonder if I put OBD1 Dizzy/Alt....is there any other wiring issues?
I figure its the same as an OBD2 LS in an OBD1 car.....
I have seen pictures of how to tell the difference but was wondering about ITR cams
I know about 97 spec and 98 spec
Is the '01 ITR cams different or '98 spec? Found some that I might look into buying then sitting on
them until I get at least some springs. Some say you need the lost motion...
Just wondering if aftermarket visors are worth it.
JDMpassword ones are hells expensive
Used JDM ones need lots of TLC to make look good again
Are aftermarkets ($60 give or take) look a lot different?
I just put 205 50 r15 with a +45 offset 6 inch rim. It is close to the fender well but seems okay.
But when I am turning kinda sharp (90 degree in a parking lot) and the suspension flexes on a bump...I here the rub.
I 'think' its rubbing on the inner fender well. I know I can take them out but...
So I searched and searched for some OEM 15" wheels
(well not that much searching...only a few weeks worth)
I found mostly bad rims with too many curbs, clear coat peeling
(overall rapid deterioration)
I would ask Guys (mostly Craigslist) what condition the rims are in on a
scale of...
So...i threw a GSR sway on my hatch. Went fine but exhaust was close...super close.
Made no noise and I figured I got lucky
But they started to rattle together at certain rpm 1200-1400 rpm (in gear)
I figured it was my new muffler and how I wanted it tucked away (inconspicuous)
Figured I'd...
I have a B16 swap (is suppose to be a Gen2)
I recently found out that the Throttle Body is OBD0 so I started poking around
a bit I looked on my head by the header (#1 cylinder) and saw the head said
PR3-3
So I Wiki'd it and found two places where people were asking very similar
questions and...
I have been told that all B-series throttle bodies are the same. But I have also been told that an H22 throttle body will work on a B16. Some say its better then OEM B-series TB's b/c of its larger size.
I am wondering what's your guys' take on this and whats the down side to an H22 TB set up...
I am on my way to the recyclers today and need some extra info before I head there.
I am looking for OEM rear sway bar for my EG hatch.
I 'think' there's three rear sway bars for the Integra
LS....GSR...and Type R
I read (online) that the LS is the smallest diameter of them all
And I've...
So I got the great idea to spruce up my interior a little....
Got new OEM floor mats and a leather steering wheel wrap
Floor mats were a no brainer....although they are suppose to be 'black'
Came to my house looking more dark gray/blue (but look much better
then what was in there since '92)...
I am looking into replacing my 92 si seats (not bad shape but faded)
I'm looking into various seats
I found some 04 civic seats. Can I run them?
I'm thinking that I can use a lot of Honda/Acura seats if I use my rails/mounts??
Is there some that go in without mod's??
I think I want Black...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.