...before I got a good one)
But it holds vacuum and now its charged (48 degrees at idle).....but it stinks
Smells like maple syrup or brown sugar (*guessing mold and nasty dust, etc)
I have been searching online for over an hour and the best fix I found is spraying deodorizer in the place...
I have been searching around for rims and keep seeing a pattern of offsets on rims for Civics.
+40 offset seems to be popular.
From what I know...offset is the difference from the center of the wheel and where the lug nuts actually attach. Positive offsets mean the face of the rim is towards...
I have a 92 civic hatch si and for some stupid reason....they never came with power windows.
I know you can put EX doors on but was wondering if you could take the switches, wiring, power window motors and window rails out and throw them on my car?
I am pretty sure its wired for it already (...
My '92 hatch suspension is very basic. I have Neuspeed race springs and KYB shocks...and camber kits.
I am looking into getting a little more performance out of the suspension and was just going to start with a strut tower bar but keep seeing these cheap combo kits. The few people I talked to...
So I have a B16A with Header, Exhaust, and OEM EG6 intake/K&N
I was wondering if there's a 'rule of thumb' for tuning the sprockets (degrees)
I always thought that you had to get it tuned/dyno'd to adjust them for maximum potential.
And yes I know they wont do too much with my set up but...
So I was walking into Kragen for a K&N filter replacement for my JDM box and a guy comes up to me and tells me my hatch is clean. I thanked him and we began to talk.
He tells me he has an EG CX Hatch with a ZC motor. It wasn't there so I couldn't look at it. I thought ZC motors were old JDM...
Sorry if this has been talked about but I didn't find anything.
My front seat belts need to be guided and push a little to want to retract when unbuckling.
One thing I found, that might work, is simple green on the unit and belt but they don't 'seem' dirty
And I found a forum on Tundras and...
I was offered to buy some JL Audio W5 or some 5 series 6-1/2" components for $200 (BRAND NEW in box)
I have 5-1/4" in the front now and I know its what is 'suppose to' be in the doors.
I've read around and it sounds like you just cut the bottom out of the basket that holds the speaker?
But...
Will the AEM for the hatch work fine?
Wondering if anyone ever put one on and the mounting marks for the intake match up with the mounting thread near the shock tower?
there relatively cheap ($100) and I need it to be smog legal...or run stock (which I don't have either)
Just wondering if anyone knew if i could do that?
I'm trouble shhoting a clutch problem on my B16 swap (I have a thread about it in the Hybrid EG-EK-DC)
If it does...I can see if that alleviates my problem
(Updates on 3rd page done Jan 2010)
I am wondering if anyone knows if the JDM B16A will pass the sniffer.
I have been researching that to be BAR'd you need
OBD1 USDM p30 ecu
OBD1 USDM B16 throttle body
Tap line for that valve that goes to the charcoal canister or get USDM B16 Intake...
I put a B16A JDM in my 92 si last weekend and the clutch relaease is like nothing I've encountered before.
If I put the clutch all the way to the ground....I hear a noise and the gears go in real rough. If I take my foot off the floor (an inch or two) it shifts like butter.
I though it...
I just put a JDM B16A in my car and have a surge/slight miss/flat powerband feeling at lower RPM's (100-2300rpm's). I have just the common three bolts and high RPM seems fine.
I was told (by a mechanic) that it 'could be' the throttle position sensor going out. Thought it would shoot a check...
My '92 EG SI with a B16 (JDM). Great success!!! Just happy to finally get it in. It was definetly worth talking to people on this forum. It all went smoothly after I after i extended wires on the engine harness (D16Z6). I extended the O2, VTEC solenoid, and VTEC oil pressure. I also ran the...
I have asked around and it seems like I can use my LS motor wiring (in a 92 EG si hatch) for my B16 swap. All I have to do is run the VTEC wiring and knock sensor to the plugs. I have some spare pin for the plugs (from junkyard) so I can make it look clean but not sure if its ok.
The reason i...
I have a JDM complete B16 swap but would like to buy a USDM engine harness so I don't have to shorten/lengthen the JDM wires on the harness
Located in Northern California
I just received my JDM B16 and have found that the wiring seems to be reversed (at least a few of the plugs if not all of them) I took all the wire loom off and haven't done any more on it since (any advise beyond labeling the wires and extending/shortening as needed?).
I got the...
I am about to do a swap (the weekend of 4/11-4/12) and need some advise on wiring. I have been searching and searching for info
My si has an LS swap in it (since '98) and I'm switching to a JDM B16 Complete swap. My car is wired for VTEC but need to know about the Knock Sensor and what the...
I am trying to find out as much info about the knock sensor wiring into my VTEC wired EG hatch. I DO NOT have the old D series VTEC ECU anymore (had an LS before and sold the old 1.6 SOHC VTEC motor 10 yrs ago)
I have been searching but need confirmation of some sort.
The Knock Sensor wire is...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.