Search results for query: *

how would i go about checking all the (banjo) wait u mean the bolt to the fuel and the filter? i made sure there was a washer on each side... i can smell gas when i go to turn it on? how do i check the dist timing i did not remove it at all? and how many grounds should my car have? i know i...

wooohoo! i got it on i took out the motor again and realized i did not change the rear mount! i feel stupid lol... anyways i got the motor in now plugged just about everything did it all my self... broke a couple things lol but i got it to crank but now the car wont go on!??

do i need to buy one of those and if so were at?

ohh one more thing so gunsnbam do i unbolt the rear motor mount and do the right and left one for now?

WHAT DO YOU MEAN BY "0" SHAPED HOLE? :confused: also i got the rear mount on already and the right one? i tried it both ways mount on trans and mount on car and i cant get it back far enough to bolt it in place. u think if i do the right one then the left one it will work? ( i cant do much...

ok i have a 99 ex and i have and i had a y8 in it now i put a z6 and i am using the z6 trans mission now my problem is mounting it on the car i can get the driver and rear mount on the car on but the transmission mount is like pushed froward about 2 inches or so i cant mount it tried messing...

i want to rewire it but i have a obd2b dizzy? and it changed from 99-00 for the dizzy to not have a engine speed cable on the dizzy? dose any1 know if it will work?

uhh help please? i found out wich wire it was if i wire it up my self will the car start with out the engine speed cable for the dizzy? and will i need to add a crank sensor? eveything electronic got changed to obd2 on the block. i had a crank sensor code on the d16y8 but it ran just fine.?

i believe you can make it vtec get a y8 head (try to do 99-00) d16y8 head vtec ecu and harness and i might be missing some things but i know you do need that for sure.

I read some magazine and Honda changed dizzy plugs on the 99

What the dizzy dose not plug in it's diffrent

Oh yea I heard harness changed from 96-98 to99-00 were. Diffrent please help!!!!

ok i have a d16y8 vtec with a blown motor... now i have took it out and have been swapping out with a d16z6 single vtec i want to keep it obd2 but what do i need to do? so far i have swapped out the alternator power steering pump slave cylinder because it was mission it and that motor bracket...

i love tien suspension i have a 00 em1 with ttien edfc best suspension out there i think .... also brother inlaw has skunk2 full suspension its awsome too but really stiff with the ttien edfc u can make it stiff or soft $2000+ set up coil overs and a little electronic controll unit;) :D

ok here is whats up i have a d16y8 with a blown motor on a 99 ek i bought a z6 and now im having probelms thinking of how im going to wire it up?? i didnt realize the dizzy was diffrent from the y8 block ( i forgot it was also obd1....) so ive been swapping out my y8 stuff to my new z6 motor...

:D get what i have ttein electronic damping force controller awsome set up :D 2000 civic si handles like a beast! :)

i did but its all good hey i been looking and behind the intake manifold i guess there was no gasket... soo could these be the problem?

no there is no lights turning on it just seems to suck alot of air into the engine :confused:

hi im new but i have a very bad problem i dont know whats wrong with my gfs honda accord its a 91 ex i did a motor swap from a f22a1 to the same thing beacause her engine rod bent... well now i got the new motor in it but when i start up the car it idls and it goes very fast till it starts...