I picked these wires up a few months ago. I like them and all but I am a neat freak and am selling them because the Red color does not flow with my car....I am going to get the NGK ones instead.
Will sell for $55 includes shipping
:D
Recently my car has been cutting out at 6500 rpm. Could this be that my fuel filter is clogged or the injectors are dirty or whatelse??
I live in BC, Canada and it gets cold here in the winter. My car sat in the garage for 4 months. I started it up once or twice to idle for 5-10 minutes.
I...
I have hooked up 3 autometer gauges (Pyrometer, Oil Temp, and Oil Pressure) except for the positive wires. I have a lot of 5 positive wires to hook up. Where do you recommend running all of these wires to??
I have RC 550 injectors. Should I send them to RC for a cleaning or should I just use a fuel injector cleaner? If you just recommend the fuel injector cleaner....which one is the best????
I have a CR/VTEC Turbo set up right now with MSD wires installed. The MSD wires have about 25000 KM on them.....what is your opinion of Magnacor wires???
I have 325 wheel HP in my car. Should I go with the 8.5mm or 10mm wires....if in fact you would recommend swapping them??
When I manually rev the car with the throttle cable, once it hits vtec there is a clicking noise. Obviously I cannot hear it when I drive because the exhaust hides the noise.
What should I check and how do I check for this problem????
I picked up a electrical autometer oil pressure gague. All I need to know is:
1. Where do I acutally tap a hole somewhere in the block or.......?
I have got all the wiring plummed up already.
Thanks
I have a 1993 honda civic oem fuel filter right now. I have a CR/VTEC Turbo swap and am making 325 HP at the front wheels.
Once I hit 6500 rpm recently, my car sets a code 16 (Fuel injectors). I have a set of 550 RC injectors. I have probably put 10000 KM on the car. Do you think that this...
Includes shift linkage, distributor, intake manifold, throttle body, wire harnass, ecu, transmission, complete engine
$1000 Shipped!!!!!!!
Email importimage@shaw.ca with any questions OR Call me @ 1-250-878-0616
JEFF
Should I use a blockguard for my CR/VTEC turbo application running 10 psi boost....mayble 12 psi boost??? If so, which brand would you recommend???
Thanks
When re-torquing the ARP head studs, would you guys recommend that I completly back the nut off then re-torque to spec. Should I do this re-torquing when the car is cold or immediately after it is shut down and still warm????
What pistons and rings would you recommend?
Is shot-peening the rods good enough if I will never boost above 18 psi boost (This is the max I plan to run)
Thanks all!
When I do my B20 CRV botom end build up, should I use stock rings or should I use total seal rings. Currently I am running the stock bottom end but I need more power.
I have a CR/VTEC Turbo with a OEM head gasket right now and I know it is failing because when I installed it, I did not re-torque the head bolts. I found out afterwards that this is absolutly necessary on a turbo motor (Live and Learn). My car is lacking power and is leaking oil out of the front...
1. I currently have a completly stock CRV bottom end with a B17a head turbocharged. I ran 301 HP at the wheels on a Dynojet at 10 PSI boost. I am not so knowledgable about bottom ends because I have never done one before. My question to you all is, what parts are required when building the...
I am selling a complete B18A swap. Comes complete with tranny (Cable), complete long block, distributor, intake manifold, ecu, shift linkage.....etc. Everything is intact and not played around with. I had this engine in my car until I wrote it off just recently. The entire unit is in excellent...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.