Search results for query: *

I am having a hard time finding the correct part number for ARP head bolts for a d15b2. We are replacing the head and figured we might as well use ARP bolts as they aren't that much more spendy. I have seen some folks say they are the same as d16's but I need clarification that they will work so...

Will a obd-0 dizzy from a b2 head fit on a z6 head?

Well I picked up a ZC last weekend. Stamped ZC and is stamped 92 above the exhaust header. I own a 91 ef hatch. This apparently is an obd1 motor... A few questions and concerns are. 1. Will the si cable tranny clutch/flywheel that I have work with this motor? 2. How can I convert this to...

As it sits now my hood is dented up from me landing on it. (won't go into details) I am also swapping in a zc, ebay is about 450 for a zc or reg carbon fiber hood. Anywhere else anyone knows of to get it cheaper?

91 DX Hatch. PM6 ECU, D16Z6 Intake Manifold (at least I think that is what it is, it has ribbs on the top of it instead of the pgmpfi) On to the issue. It runs great performance wise. The only issue is that it idles like shit, it stays above 2.5k at all times and goes to 3k until warm...

Got it in 15/16's MC, along with a set of cermic pads, brembo blanks and SS lines. Have a problem with the right side caliper though. Its hanging a little bit. I went to the parts store and picked up a new caliper. Didn't come with the part that holds the outside pad. I tried like hell to...

Update: These weigh 26lbs with the huge allseason 186/65/14's on em. Plus some close up shots. The low down is that I have a set of 14's and 16's and I need a set of 15's. Can be any brand just need to be light. Don't really care about rash too much but they have to be straight! I will...

I picked up a 15/16 from a 88-91 SI Lude. The bolt pattern is the same to bolt up to my 91 DX Booster. Just want to make sure the thing will work as I can't have much downtime on my daily.

I picked up a cpl of trailing arms from a 93 DA to swap on my 91 DX hatch. Is anyone 100% sure that they will fit? I eyeballed it and they look identical in length/fitment. Before I rebushing/rebuild them I want to make sure they will swap on. I have the WHOLE rear suspension out of that...

Hit me up in PM if you have some you would like to get rid of...

Lizard Heat rock. Barely used. 15 OBO. HP DeskJet 855C In great condition. Prints great. Power Cable and 20 ft. Parallel Cable inclueded. All it needs is a color cartridge. 30 OBO Hypertech Chip for a 96 Mustang GT 5-Speed. Works great. Don't need it as I am going with a custom...

The car is pulling to the right on Accel. on Deaccel alignment is fine. Out of gear alignment is fine. I can also actually move the rime Vertically maybe a 1/16 of an inch back and forth. Any ideas what the issue might be? This is on a 91 Hatch. I am tearing it down tonight to look at it.

Ok, I have a set of 14in alloy rims and a set of 16in alloy rims. The 14's are probably close to 5lbs lighter a piece. Which should I purchase a set of slicks for autocross for?

I have a 91 Hatch I was entertaining doing a swap to a b18 in. Does anyone know of a reputable shop near St. Louis that would undertake the project?

Just finished my first SCCA Solo2 Autox. Ran a pretty good time and took 3rd in STO. Came in behind a modded M3 and a modded Porsche Boxter. My current setup to pitch the rear end is rear strut tower / Tie bar. I put a set of Parada spec 2's up front and a less sticky tire sumitomo all...

Hey all. Quick Question. What springs would you guys suggest for a 91 hatch that has Toykio HP shocks? I would like a 1.75 to 2 in drop. I am just tired of the Generic Springs that I had put on. They are so stiff that if I hit a big enough bump it can knock the wind out of me! Thanks for...

I just had Toykio Blues with some generic adj. coil overs put on. I also requested a 4 wheel alignment. He Charged me 4.5 hrs of labor @ $65 an hr. He also Charged $79 for the Alignment. This seems really high to me... Total came out to be $372.45 This was on a 91 civic hatch dx.

This f'in problem has been plaguing me on these cars for some time now. Some times my 89 will refuse to start. It will turn over, it gets gas but no spark. I eliminated some harnesses and the problem went away only to return once in a blue moon. The problem is I bought a 91 hatch and it has...

Hi guys, just wondering if any parts besides the mpfi swap are interchangeable? Is the Cylinder head any different? Different Cams? Is the bore/stroke the same? Thanks in advance for any advise or opinions...

Hi guys, I just bought a 91 3dr dx. It has the crappy 1.5 in it. I was wondering if there is any oem intake manifold that will work on the motor besides the original. Perhaps the si model intake? Although its rated at its peak hp and tq up high in the rpm range it feels like it hits a brick...