Hey guys, I'm selling all my Civic aftermarket and OEM parts. If there is ANYTHING you need that I don't list, please contact me. These parts are cheap, cheap, cheap. I'm just clearing everything out. If pictures are needed, don't hesitate to ask. Most of these parts I just want gone, some...
Hey guys, I looked around for the most appropriate area to post this thread. Please don't get mad if I posted in the wrong area. I have a steering column issue. The story is; I took out my dash to put a new cabin wiring harness on the inside of the firewall because my old one was hacked. So I...
Ok, here is the speel about what I have currently done engine wise. I have rebuilt my D16a6 block with all new:
-OEM pistons
-OEM wrist pins
-OEM gasket set
-OEM oil pan, because my old one had a lot of larger pin-holes in it!
-OEM thrust washers
-NASCAR true-circle piston rings
-Clevite...
Hey; I am looking to find out which high-performance oil pan I should use on my D16a6/D16y8 "mini-me" turbo project. I just searched and could not find a performance oil pan. I think Moroso makes one, but I do not know I will check again. Any suggestions are greatly appreciated, thanks!
I have a lot of EF parts for sale, these are not limited to any of the following parts list. In saying that, I have a lot more stuff that simply needs to go for numerous reasons; the main reason being is that I have upgraded to newer or aftermarket parts. Now, on to the non-official parts list...
Hey, I am just looking to find out the valve stem outer diameter. I just do not have a Haynes manual for this engine, and I am only rebuilding the head where necessary so it is not even worth the $20-$30 a Haynes manual will cost. Thanks in advance!
I am planning on cutting my "C" plug so it will not show in my engine bay. I am planning to simply cut each wire and extend it by 4-5" each; solder, heatshrink, and electrical tape all connections. I just want to know; in the future would I regret this move or would I just simply put the engine...
Hey guys; I was at a carshow earlier and saw an 88-91 Civic HB with a clear hood. I have never seen one before and thought it was amazing. I figure since I am making my 90' Civic HB into a show car, I should get one. My engine is going to be show quality, and I want something to be able to show...
If you need an OBD0 - OBD1 conversion harness a.ka. jumper, let me know and I will make you one. I have all the material and know-how and I will charge less than what they sell for elsewhere. Thanks!
Ok guys, so I have started a wire tuck on my EF and it is definately a work in progress. So far I have tucked the; headlights, horn, washer fluid resevoir tank connector, markers, indicators, wiper motor, engine bay fuse box (now on the inside of the cabin), and obviously the multi-ground behind...
I made this thread particularily for my 1990 Civic Cx (converted to Si). I am going to post up many pictures. I am going to just post miscellaneous pictures, except my engine rebuild because it is in a different thread.
I just thought this would be something some people may find interesting; the American version of the D16y8 is an EX, while the Canadian version of the D16y8 is Si. My dealer, honda dealer that is, told me this when I was asking about parts for the head.
I have a COMPLETE D16a6 Intake Manifold for sale, it comes with:
- Intake manifold
- Throttle body
- Injectors
- Fuel rail
- Fuel injectors
- MAP sensor
- EACV
- IAT Sensor
- ALL Vaccuum Lines and Hardware (nuts, bolts, and banjo nut) Included
*I do not have the manifold-to-head nuts (they can...
As the title states I have a D16a6 Block, D16y8 Head, and D15b2 Transmission. I was wondering what you guys think of this crazy combo. Open to any suggestions!. I found an excellent thread on rebuilding a transmission, so I am in the process of tearing it down for shits and giggles. The D16a6...
Hey guys; I'm doing a homemade turbo setup for my stock a6/y8 mini-me combo. I am just trying to learn about how to do this; price and quality effective. I have the D16a6 block at my local machine shop getting the machining done, then I'll be assembling that as well. Once I get it back I am...
So I decided I would do a mini-me, so I pieced the swap together bit by bit. Now I have everything. I decided to do a COMPLETE rebuild of the block and head. I feel that I spent too much money on this swap, please let me know what you guys think.
D16y8 Head cost me $100
I have done EVERY gasket...
Hey; I have a couple parts to sell from my 88-91' EF Civic body, as well as my 96-00' D16y8 engine. LOWBALLERS WELCOME, Here goes:
---> 88-91' Civic/CRX Stock Headlights
---> 88-91' Civic Interior Door Panels (non-Si)
---> D16 Lightweight Crank Pulley
---> 3Dr Hatchback; Doors x2
---> D16y8...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.