Search results for query: *

I have a Cr-Vtec Turbo set up in a 93 civic hatchback. I am running Hondata stage 2 with boost and am using Pl-8M 550 cc RC Injectors. I keep getting a check engine code 16 (fuel injectors) and code 43 (fuel supply system). Also, I get a code 41 (02 heater core) but I just changed it recently. I...

I have a 92 Civic Hatchback with a Cr-Vtec Turbo under the hood with Hondata Stage 2 with boost. I am running RC 550 Injectors (Rc550-PL). I have come to realize that i do not have a resistor box. I thought I had one but it was a relay box for the headlights. Sometimes the codes come on when I...

Background: B20 Vtec Turbo with Hondata Stage 2 with boost Problem: I engage the throttle slowly and the is hardly any boost (That is obvious). But when I hammer it and it boosts up to around 4-5 psi. The car stutters and then I lay off the gas. Once it does this stuttering, I get a Check engine...

My car runs for about 15 minutes then I get a code 16 and code 43 come up. I recently had my main relay re-soldered, fuel injectors cleaned and new fuel filter installed. I thought that these checks and replacements would rid of these annoying codes. -I am going to change my O2 Sensor. -I...

If you have one or have any sort or idea where the best place is to get one, please let me know. :worthy: Jeff

These springs handle awesome and make for a tight ride. I am only selling them because I do not like my car so so so low to the ground!! Jeff 250-878-0616 :rolleyes:

I have an erratic idle right now and have come to the conclusion that my IAC is defective. If you have one for sale and know it iis a good working condition part, please let me know some way or another. If you want to call me, my number is 250-878-0616 (Jeff). :spin:

If anyone has one of these or can get please PM me. :worthy:

I am have a very tought time installing my injectors. I have the correct seal rings that go into the intake manifold from the dealership and a set of 550 RC injectors. I have lubed up the seal ring and around the injector base and the bastards are really hard...actually impossible to squeeze in...

I am curious about those who have a B20 Vtec or B20 Vtec Turbo setup like it so far. Post any problems or positives about the whole CRV swap idea!!!!! I peorsonally have a B20 Vtec Turbo and like it a lot.....except for the siamese sleeves. That is why I am only running 10 psi boost!! Post...

On the JG edelbrock intake manifold, there is no where for the Fast Idle Valve to be bolted onto the intake manifold for coolant to flow through. Can I just bypass the FIT Valve housing and just run a line from the thermostat housing area to a hole in the intake manifold so it runs through. JG...

I purchased this gauge from a local tuner shop a while back and he has since closed the doors. I was going to install the gauge then I said.....Fuck it!!!! The gauge reads from 0 psi to 100 psi with small increments so you can really accurately tell where the oil pressure is! I will sell the...

I need the front driver side lower motor mount to the underside of the frame from a 94+ Integra. The unit hold the p/s and shit within the bracket and has a piece that bolts to frame. I need this piece becaue my engine twists when shifting gears.

I have a set of 550 RC Injectors....they are great except the O rings, cushinon rings and seal rings etc. are cracked. I think that this is why I am getting the check engine code 16 (Fuel Injectors) come up. My question is: What O rings, cushion rings and seal rings do I use? I have a B17a...

I recently had a code 16 come up and checked everything back to the PGM-FI main relay. I had the unit re-soldered because of cold joints and dry joints. This fixed the code 16 problem, but now I am throwing a code 43. Please help!!

I plan to rebuild the bottom end of my B20B this winter. I am going to get the block resleeved and upgrade the pistons. My question is, should I go with the 84mm sleeve and piston combo? OR should I go with the 84.5mm sleeve and piston combo? What pistons would you recommend for the B20B Vtec...

:fuckyou:

What should the oil pressure be on a vtec engine: At idle, In Vtec and not in vtec????

I threw this code when I hit 6500 rpm. I just shut the ignition off for a second then started it up again. The cel went away but I know that this code is still in the system until the problem is resolved. Any suggestions on what to check?? I have changed the fuel filter and this problem still...

I was wondering if anyone can get this product????