Search results for query: *

I got a built turbo b16a that I'm planning to push at least 400hp and was wondering what head gasket should I use? Well I kind of rushed the build at 1st because I couldn't get my arp head stud in time and needed the car to run so I used the stock bolts with a acl gasket kit. Now I'm pushing...

Hey guys! I got a Innovate LM-1 and Rpm converter and I want to log boost input on my stock map sensor. Does anyone of ya know what to set the configurations at for the stock map sensor on log works 2?? Thanks!

Hey guys! I was wondering if anyone of ya know how I can tell whether or not the arp headstuds I have i for a b18c or b16a? I got it used from a friend of mine, which came out a b16 but I was told its for a gsr! Does anyone know the length of the arp studs for a b16? Thanks!

Switching from Crome pro to eCtune Hey I was wondering if anyone here switched over from crome pro to ectune and do ya reccomend it? Or is Crome pro good enough? Thanks!

Hey guys! I wanna know how can I tell if a trans is from a JDM 90-91 integra XSi or a USDM 90-93 integra LS? I mean they both say S1 but how can I tell or test which is which besides installing it in the car and testing out the gear ratios on the road? The motor it came off is a B16A but trans...

Well I'm almost done with my turbo b16 build and I'm now deciding what brand/clutch I should get? I'm currently runnin a ACT HDSS clutch in my cars and I like it! I'm aiming for 350+whp so Im looking at most likely a 6 or 4 puck disc (stage 3) or so But I'm not sure what brand to choose from...

Hey guys! I'm planning on doin a quick overhaul on my girls turbo'd B16 and was thinking of putting CTR pistons in! I was looking on ebay and saw a kit with ctr pistons and bearings made by nippon for a low price! Anyone tried these pistons before? I'm planning on high compression with low...

Hey ya! I'm building a b16 for turbo. I'm finish with the block (9:1 je pistons with eagle rods, etc.) Now I'm plan on ordering my valvetrain and can't decide which ones to get. I'm going to be running ctr intake cams with a gsr exhaust cam maybe 9k rpm on a head thats P/p with a 3 angle valve...

Hey guys! I was wondering what will my friend need to do this conversion in a integra! I know I'll need the trans, clutch pedal, clutch lines (w/master& slave), shift linkage, conversion trans mounts, clutch and flywheel (w/bolts) and a 5 speed ecu. I mean I did a 5 speed conversion on civics...

I was just wondering what is the main diffference between them two? I know its something to do with datalogging (wideband feature), but what else? Do I really need it? I was thinking of getting that package deal on XENOCRON or just getting a Emulator and a wideband. what ya reccommed?

Hey guys! I was wondering how much pressure do I load into the cylinder when performing a leakdown test?? Thanks in Advance!

Hey guys! I'm gabout to swap a h22a into eg (94 dx hatch) sometime soon! It's a 97 h22. Which harness will I have to use? I have the p13 ecu. Do I fit the dx harness on the h22? Or do I modify the h22 engine harness? What else wiring (electrical) do I have to worry about??

My problem is that the car starts sputtering (stalling! wont go any more) when I hit about 5-6psi of boost! I'm running D16z6 with a t3/t04e turbo (10psi) with DSM 450cc injectors managed with crome. The car runs fine, idles great, runs well in low load but starts stalling in 5-6psi of boost no...

Hey guys! I have a b16a with JE low comp pistons and eagle H-beam rods! I have the rods installed, But I was told that I have to notch it in order to clear. It spins freely but I want to make sure before I slap the head back on. Does anyone know if I have to notch the block to clear the rods??

I'm currently running crome on my b16 turbo. I'm planning to up the boost from .4bar - .6 bar or maybe little more:D . When I do up the boost, I'm planning to run my friends wideband to see if the crome basemap is safe. If its a little lean here or there, Do ya think I can fine tune the fuel...

Hey guys! I'm helping my homeboy put together his crvtec block. He already has high comp pistons with pr4 rods and stock crank. He spun rod bearing #1 resulting in gouging the crank, so the crank ain't reuseble. So we're planing on changing out the crank and rods also! Can we stroke it? what...

Hey guys! I was wondering where I could get the valve lash socket tool tp do a valve lash on the b series vtec head (socket with that handle and hole for the screw driver)? Its kind of in there to use a open end and a flat head! Also the valve spring compressor (universal overhead) I have looks...

hey guys! I'm done with my turbo install on my EG 4 door sleeper! B16 with turbonectics t3/t04b h-trim. .63 a/r. Problem is my exhaust is still stock so I get a big lag and I am thinking of getting a full after market exhaust system. I'm thinking on getting a Greddy SP2 or Tanabe hyper medalion...

Hey Guys! I'm putting together a turbo kit for my daily driven eg8 with a 1st gen B16A. I just want opinions on what turbo size I should run for quick spool ups and great street power. I'm looking towards getting a Garrett t3/t04b .60/.48 or t3/t04e .57/.63 from West-coast turbo. Thinkin of...

Hey Guys! I'm finally putting together my B16 turbo build project.. But I didn't buy my connecting rods yet! I'm looking towards Eagle H-beam Connecting Rods. Hopefully maybe break 350-400 whp! Do you think these Eagle connecting Rods will be okay? Or anyone have suggestions! *Remember I'm...