I have a 90 hatch with b16a swap and noticed the car makes weird
Noises when u drive from a stop, sounds like knocking i looked under the car
and the passenger side half shaft is not in the tranny all the way like it should be. could it b the
wrong halfshaft??
okay i just got a 90 civic hatch with a b16A swap,the car is my daily and has a few problems that need fixed soon.
1. car runs rich, has adj fuel reg,fuel rail, 255 fuel pump how can i get it to run right? It smells really bad!
2. car uses a lot of oil but it is leaking, noticed alot of oil...
Alright, have a 90 civic hatch. The door light in the dash is always on even when both doors are shut. But as soon as i start driving the seatbelt light flashes and beeps the whole time! This is very annoying. Some kid told me it was the door sensor but i tried taking it out and eveb replacing...
I have a 97 integra ls with an ls/vtec swap. b18b block and a b16 head. Runs good and strong. When i first got the car it would surge up and down till it warmed up then it would idle fine and steady at 800rpm, this was at the end of summer. when it got cooler it started to idle surge in neutral...
Alright swapping over b16a into a 91 ed
This is what I have done:
-dpfi to mpfi ( accidentally got the inj numbers backwards. No biggy)
- converted all obd0 plugs on the harness to obd1.( dizzy,alt,injector clips fit)
-dropped motor in hole everything mounts. No clutch in the tranny. Going...
Alright I have a ls/vtec with pr3 head. It has a noticeable tick which i first thought was the injectors but I asked the guy I bought the car from and he said it has crower valve springs and retainers and thats y it is ticking. He said I need to run bigger cams like skunk2 stage 2. For it to run...
I have an ls/vtec with a b18b1 bottom an b16 p3 head. I've had it for a week now and it seems to run fine.. exception of it warming up it revenue up and down. Anyways it appears to use oil alot. This morning the cel came on for the first time and I checked oil and it was almost dry. does anybody...
I have an ls/vtec swap in my 97 integra. the head is an obd1 b16 pr3 i beleive. anyways i noticed today when i open the hood while it was running that it sounds like the head is ticking? its not very loud but noticable. is this normal or should i look deeper into it? I though maybe alot of these...
Alright so i just got an integra rs with the ls/vtec swap. The guy said the ecu is chipped when i looked I couldn't see anything but i did see a chip that my other p28 didnt have. It looked like it was ment to be there though because on the other p28 I have there is a spot for it. Anyways the...
I'm putting a b16a in my 91 civic hatch with a gsr header.. the header has two sensors that are one wire and my harness only has one plug for an o2.. so how am I suppose to hook it up? Just use one sensor?
Alright so I'm driving along in my daily db8 yesterday going about 65 drop it into fourth to get a lil more speed like usual.. then I hit vtec at about 5-6k and right after cel comes on! This morning I start it and no cel but when I did the same thing it did it again and vtec didnt even kick in...
I have a 91 ed hatch with a b16a.. it appears that it does not have a canister but there is some kind of red hose coming out from the fire wall to the engine bay. can anyone tell me the proper way this is setup? idk if the canister is needed or not. or maybe it didnt come with one.
alright so im in the process of doing a b16 swap in my ed. Ive seen several obd0 to obd1 conversion diagrams and my question is does this work on both dpfi and mpfi? bc the harness was dpfi. also i was unraveling the cluster of wire that led through the fire wall and there is a wire going from...
i am putting an obd1 ready b16 in my 91 hatch and the wiring harness that the guy gave me is a clusterf***. He said he had to convert it from dpfi to mpfi. but the wires that go to the injector plugs are not consensent at all! It just looks like a shitty stereo install. Im sure there are many...
I have a b16a swap im trying to put together and when i go to put the dizzy on all holes line up exept for on the top hole it barely catches so the bolt wont go through. and you cant turn it any farther cuz the housing hits by the vtec solinoid. so thats as far as it will turn in one direction...
I have a 1997 civic coupe 5 speed with the d16y7 in it. Well anyways i just bought a b16 full motor swap.. of course not everything is there but the guy gave me two ecus and told me they would plug right in to the civic harness. i knew that couldnt be true because his ecu's were vtec, a p06 and...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.