Search results for query: *

did the car have the rear speakers next to the rear seat? if so how much for the set up?

is this hole 1/8th inch NPT? or is it M10X1.0?

Well i did some research on d-series.org and found i CAN put the y8 head on my motor. It is actually is a very good combo for turboing. It will void around 8:1 compresstion. But very bad for Na. I could have the head milled about 40 thousands, but it would cause a little grief with the timming...

Ok so will a d16y8 head fit on this d15z1 block? I have a line on a d16y8 motor for $75, but it has a rod knock. So if i get this motor, will the head fit on the d15z1 block with out piston/valve clearance? I mean shit i already have my wireing harness and if i just take all the sensors out of...

I was also thinking, what if i was to push the vtec pin though the rockers (like if the vtec solinoid was active) and then weld the pin in place?Then disconect the vtec solinid. Then (in thery) the motor would run like a non-vtec 16 valve, but with a milder cam profile. I weld for a living, so i...

I dont know man. How much would a head at a local Junkyard go for? There is this local JY that has like 3 90-91 si hatchbacks. But i dont know if the head off one of those is worth it. If i get one of these heads then it wont be vtec. Witch i am ok with, but then what do i do with the wiring...

So i have another ? Can i just swap the D15Z1 head off, and put like a Ex of Si head on the D15Z1 block? Or do the water holes not line up? Or will there be a valve to piston clearance problem?

yea what he said^^^^^^^ Those pistons on this d15z1 block? I'm no expert, but that wouldnt do anything unless the pistons are domed for high compression. Oh and what is a A6 head? You also said mabee a vtec head, i already have a vtec head, a shity one i am being told, but a "vtec" head none the...

I dont really know how much. I mean if i could get rid of this engine i wouldnt mind spending up to Mabee $500 + what i could get for this engine. I would like to get right arounf 120-150 HP. My rail dont weigh much more than 1300 lbs. so alot of HP is not nesasary.Like i said if i could just...

I am kinda new to hondas so dont flame me please. Anyways I have a little china sand rail that i put a d15z1 motor in and as i said i am new to the hondas and i think i fucked up when i did this swap. I used a p-28 computer, and made my own wire harness with info off this site. The engine runs...

Like the title says. I am puting a D15Z1 in a sand rail. I need to know the bare minimum wires that i need to hook up. I have a P28 computer if that helps.

So i just found out the motor i got from the junk yard is a v-tec motor(D15Z1). So what computer do i need to work? Any v-tec computer will work right? Single and dual cam v-tec?Or just single cam v-tec? Shit i'm confuseing myself writing this. I'm an idiot.

Really? Dame! Thanks for the quik reply

Also i was looking around and i saw something about the color of the valvecover meaning something, is this true? My engine is out of a 1993 civic coupe and it has a black valve cover does this mean somthing or no?

I have a Pm5-A30 computer. it can from a 91 civic hatch. I have a 1993 civic single cam non-vtec engine will this computer run this engine. Oh and i dont know if this helps but i still need a distributor so if i need a specific one to make this computer work with this engine. Ps. I dont know...