Recent content by riceburner5

"i just got done installing a obd1 h22a in my 97 civic with a obd2 to obd1 conversion harness on p13 ecu, and when i started it up the rpm just start to climb up to 4000 rpm and stays there. now, i checked my throttle cable and there's still slack on them. what else could be causing this. pls. i...

thanks guys, i found my problem. it was my tps sensor, i replaced that sensor when the motor arrived cause it got damaged during the shipment and it was out of tolerance. yea, i swapped my tps and map plugs at my last swap but this time i made sure so i wrote on the plug itself, thanks though...

i just got done installing a obd1 h22a in my 97 civic with a obd2 to obd1 conversion harness on p13 ecu, and when i started it up the rpm just start to climb up to 4000 rpm and stays there. now, i checked my throttle cable and there's still slack on them. what else could be causing this. pls. i...

i didn't drive my car for 3 weeks and when i pushed the clutch in, it stayed on the floor. i check my clutch fluid reservoir and it was empty. what could cause this? is my slave or master cylinder going out? pls. help and thanks

is it safe to put platinum iridium plugs on an h22a engine? cause i've heard of melted platinum plugs on vtec engines and it doesn't sound good, but i was just wondering if it's safe or not. any advice would do, thanks.

i swapped out a b&m fuel pressure regulator along with the gauge. my fuel pressure is at 30 psi right now and when i'm driving and hit the vtec point, the engine gets louder like what a vtec does, but there's no power. it even feels like it slowed down. could this be because of my fuel pressure...

does anybody knows what the light that looks like a "catalytic converter with heat coming off of it" on the instrument panel? i have that on and i was wondering if that was the oxygen sensor heater or something. pls. help

well, is there a way to change the civic's bolt pattern of 4x100 to 4x114.3, i'm just wondering?

does anybody knows if the 92-96 prelude hub unit wil bolt on to a 92-95 civic hub with no major modifications, front and rear? if anybody got any ideas, pls. feel free to drop a message. any help would do.

hey dohcvtec_accord, so a knock sensor problem wouldn't affect the vtec engagement? i thought that when the check engine light is on, your ecu is running in "limp" mode. but then again, it might be the egr problem. i'll try fixing it this weekend and i'll post an update. thanks again everybody.

i tested out my civic last night and when i was done, there's this whirring sound when i have in neutral. but when i press the clutch in, it stops. any ideas what this may be? also i don't feel the vtec kick in, you can hear engage cause of the louder growl but i t does nothing. as a matter of...

hey man, i myself owns a 93 handa civic vti (vx in da states) with a jdm h22a. i'm station here in japan and parts for prelude are dimes a dozen but anyways, here's a site you might want to check out. http://h22acivic.com there's another one but it seems to be out of service right now. i still...

i was wondering if there was a way to change the civic's wheel offset from 44 to 42 or vice versa. does it include changing the whole stud assembly? pls. help and thank you in advance.

does anybody have a picture of a knock sensor on an h22a engine or a very good description and location of it. also any suggestions on the ecu problem code 12 (egr:exhaust gas recirculation lift valve). is this wiring or the egr itself. pls. help and thanks in advance.

i started driving my h22 hatch and started to hear a whirring noise on 2nd gear and 3rd gear as i go but when i push the clutch in, it stops. can this be my throw-out bearing or my synchros. i've been busy this whole week with work that i didn't even got a chance to really look at my car, yet...