Search results for query: *

alright, now I swapped the wires around, still the same problem, doesn't want to start, idles ok but u hit the gas wants to die. 2 codes present, #4-ckp #9 cyp :blink:

It is a grey plug, obd1. I have them hooked up to blue wires. I am getting two codes #4-ckp and #9-cyp. anyone know the wires for these sensors, where they hookup, what color, anything?

just got the swap started, but throwing a code, 9? chilton says cyp? that is in the dizzy correct? I have two wires ran from the ecu clip, c1 and c2, through the firewall connected to two wires into the dizzy. I have obd0 to obd1 jumper. request knowledge?

I have two wires left to hookup. C1 and C2 on obd0 clips, My info says Crank angle sensor, where located on the motor? B16a motor XSi, ys1 tanny

There are two vacuum line fittings one is offset towards the front of the tb then one dirrectly on top. the one on top? I was told it goes to the charcoal canister? Can it be plugged? I tried to take it out with an ez out, it broke inside, thought about drilling but metal shavings don't...

The vaccum line directly above the intake on the tb is broken. Is this a problem. I tried an ez out, broke inside, it is plugged up really good now. is this going to cause problems?

I got the swap in it turns over, yippy. Used a little starter fluid ran for about 5 seconds, now the obd flashs= two short flashs and pause then four quick ones. I read my chilton and can't fiigure out what the code or codes are, any help?

Thanx, swap is almost done!:)

Hey I want to move my battery to the hatch(trunk). Do I have to run the ground wire back or can I connect the ground wire off the motor(tranny) to the shock tower? and the Neg off the batt to the rear shock tower? Anyone have a better Idea or experience?

Trim the black housing on the one I have, I don't understand, explain? One for and 90-93 Integra will work?

the clutch cable is two or three inches short? any remedies or replacment cables that work?

thanx go it?

So I use a 90-93 teg hose for upper and 90crx lower? opinions? I will just get 5/8 hose for core, thanx?

WHat hoses to buy, Radiator and heater core?

definately speedo cable, two hoses are pinched off, motor from hmo. 90-93 xsi b16a. cable trans. hey this motor also came with something missing on the back of the throttlebody, is that the throttle position sensor? round hole with a gasket.

what are the two hoses coming out of the speedo cable housing? Can they just be plugged. 93 b16a

I need to get my harness back to stock the last kid who had the car did a number on it. I need stock ecu pinnouts and wire colors. I have extra wires that need to be hooked back up. I also have a obd1 pr3, anyone know the pinnouts, I can't find anything on it some people told me it doesn't...

Anyone know the ecu pinnouts for a obd1 pr3. As far as I can find it doesn't even exsist.(i have one) I need to know the stock pinnouts for a dx ef civic. and the colors of the wires so I can re-wire it back to stock, the kid who had it before did a number on it. Any help?

alright, this car is a real headache, the kid who had it really did a number on the dx harness, I have to buy a new one should I just buy the dx or get on out of an si? I am just going to buy all the stuff from rywire but I don't have an unmodified harness. What to do?

so change the plugs on the dx harness to the ones off the new motor, can I extend the wires if needed? and get the conversion harness. where could a get the plugs for the obd0 ecu, I would like to make a diy harness conversion.