Search results for query: *

so i have a 00 hx obd2b, auto, i am swapping it to a d16z6 manual. i have the motor, tranny, linkage, p28 ecu, obd2 to obd1 jumper, whole pedal assembly, well everything. i am just wanting to make sure about the wiring. i am still a little worried about the engine wiring. is there anything that...

can i use the z6 obd1 engine, head, and im with my hx obd2 harness, obd2 ex ecu, and my hx distributor? will that work or cause a bunch of crap or can i use just the obd1 z6 vtec head with my y5 im and my hx distributor,and the obd2 ecu? would that be better? i just was thinking of putting a...

d16z6 t3/t4 turbo with 8 psi, i just installed an aftermarket oil pressure gauge, when i first start my car when it is cold, my oil pressure goes up to like 75 psi, after about 5 -10 minutes of driving my car the oil pressure drops to zero at an idle. i have the feed line ran off the back where...

i have a d16z6 with a t3/t4 turbo,chipped p28 with uberdata,my alternator went out, i replaced it and a brand new battery. i reset my ecu,cause when the alternator went out, my vtec stopped kicking in? i have checked the wiring, the oil, and have tapped the vtec wire on the positive terminal...

i can't get boost in first gear, it is a t/4 xs power turbo on a d16z6? any ideas?

what is the hole on the top of an external tial wastegate for? someone said it was for the wastegate adjustment, but i don't know. and there is nothing in its place. i know this is a stupid question, but i am just learning about turbos. thank you.

i have a d16z6 vtec with an xs power turbo setup, chipped uberdata p28 in a 92 civic dx. just rebuilt the motor with low compression vitara pistons. my question is, when i am on the highway in 5th, if i bring the rpms to around 4500-4700,the check engine light comes on and stays on till i shut...

can i put a d15b crankshaft into a d16z6t with d16z6 turbo pistons if i use the d15b piston rods or the d16z6 piston rods. is it even plausible?

i have a 95 civic cx, i took the dash out to get to the heater core, everything was good, put the dash back on . I made sure the gounds were all back,but if i turn the key on and turn the headlights on everything goes dim, if i turn the hazards on at the same time, i hear buzzing from a relay...

i was thinking about putting an 88 integra d16 motor in my 95 hatch till income tax time, i would be going from obd1 to obd0. will this work? and what would i have to do to do it. it will just be temp. so i can get to work and back till i get money. please help.

i put a b18a1 obd0 mpfi into 91 civic dx with dpfi zc 1.6. i wired in the the injectors and the two wires from the distributor, i keep getting crankshaft positioning sensor code. all the wires that i cut going into the ecu, i reconnected them to the same spot with the other wires. so all the...

how do i get the tensioner to tighten the belt once i get the belt on? because it didn't tighten last time? first timing belt!? :blink: :wtf:

my b18a1,wich is in a 91civic dx,dpfi- mpfi, well it is cutting out at 3500?sounds like the rev limiter. my ecu is putting out 4 short blinks, wich the chilton says it is the crankshaft pos. sensor?what- where and how do i know or check? my cooling fan wont come on . checked all fuses,it is...

ok, i have a b18 a1, i am putting it into my 91 civic 4 dr., my old motor was a zc dpfi 1.6. i got a new ecu from a 90 integra,same year as the motor and also rs. i bought a harness for a 90 integra 1.8. i also bought new motor mounts from innovative mounts.i am confused about my harness hooking...

i have a dual point programmed fuel injection intake manifold, im putting the b18a1 from a 90 integra rs, didn't reallize about the injector plugs, if i get a harness from a 90-93 integra (obd0), will it work ?im confused the only thing holding me back, is my harness crap, not sure about what cv...

can i use my sohc 1.6 obd0 distributor for my new b18a1 dohc obd0?

im swapping a b18a1 into my 91 civic 4 dr.dx from a 1.6 zc motor, do i have to get axels from a 90-93 integra or can i use my civic axels with the b18a1? please help.

im trying to help someone swap motors, it is a b18b going in to a 1990 integra. the motor, he thinks is out of a 94? can you use the wiring harness from a 1990? the distrubuter plugs don't match and they think they have to pull what looks like a freeze plug outof the b18b to put a sensor in from...

i am swapping a b18a1 into my 91 civic dx, it allready has a zc motor in it. i need to know if i need to get different shift linkages, can i use the stock motor mounts from the b18a1? and can i use the shift linkage from a 90 or 91 integra? and will my wiring harness work? i believe i should...