hey guys i've coem across a big problem i have a 1995 civic lsi and im using the wiring loom that came with the b16a which is out of the del sol sir 1992 why would the car run like shit with the original ecu ? anyone help lolz and i keep getting a code 3 which is the map sensor and i got the map...
B16a JDM map Sensor problem
ok guys i've got a problem my map sensor the 3 ecus 2x p28's chipped and virgin p30 jdm ecu display the code 3 map sensor but i have wired it up direct to the ecu can someone give me a diagram on what wire goes on the map sensor and where on the ecu i know its D17...
hey guys im runnign a 16a with a p28 chipped ecu and a stock b16a map (p30) now the car is running very good but the idle is shit goes slightly up and down but thats not my worries. my worries are when i start the car it's like its going to stall then the iacv kicks in and brings it to 1000rpm...
hey guys i'm struggling a little with the map files well building a map file i've tryed the original b16a map and runs like shit and idles bad as if its gna stall then i tryed the b18 map and jst a lil acceleration makes a loud pop noise what shall i do ? or does anyone know how to make me the...
hey guys as you know i have a b18c4 engine i got hatch now and want to put in a b16a2 but want to know what will happen if i was to put b18c4 cams in it thanks guys.;)
Hey guys just here to tell you that my swap is completed and is running perfect thanks to the guys on this forum. i would like to thank everyone thats helpped me specially 1988hondacrxsiR1, formby, fixngo, 92civichbd15b, and everyone else that has helped me thanks :) i have some image videos...
hey guys am really having difficulty with the dizzy not sparking. there is power going to it rotor changed coil changed still no spark changed map sensor as well but not sure what else. fuel relays click and fuel pump works the only thing not connected is the o2 sensor because the wires have...
hey guys as i am from the uk i have done a b18c4 conversion into a civic lsi 1995 which originally had a d15b7 engine now i replaced engine tranny axels and used the b18c4 engine harness and connected the direct plus up to the d15b7 wiring which goes to the ecu my problem i dont know but i try...
My B18C4 Wont Start
hey guys even though i dont have a started motor is it possible to bump start the b18 ? my starter should take 3 days but i have rebuilt the whole engine but tryed a little bump start wont start though any suggestions and yes i am still using the vtec e ecu will that be the...
my b18c4 wiring harness is perfect apart from 4 wires which are the o2 sensor wires how do i go about wiring this up does anyone know the wiring code and functions ? thankz guys so far this forum has been superb on evrything
hi since i am new to swaps i was going to try and fit a s20 gearbox 2 a b18c4 but i've been reading and its gotta be bseries can i swap it for a 1M gearbox or a gearbox out ov a 1997 2.2 Prelude the engine that i previously got was a d15z3 vtec E and the gearbox had an lsd on it but i used my...
hi i have a little problem with my b18c4 swap well i got the harness with the engine but someon has cut the o2 sensor wire off so i dnt know which wire is which. i was thinking a copy of the b18c4 manual if there is one tryed searching sooo many didnt find the right one btw is the b18c1 same as...
hi guys i have a B18C4 Engine Crankshaft is gone did go to engineers to get it grinded but no one does the rod bearing sizes for the grind. what can it be used for its a good engine just the engine has been running on lack of oil which has caused the crank to grind the shells off
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.