how much psi can I boost??

[turbosivtec]

Yeah I was wondering, whats the max boost i could push with my d16a6 motor?
specs:
stock internal
450cc injector
greddy td04 turbocharger with internal wastegate
jdm intercooler
afc tuning, stock ecu
so right now Im boosting 6 psi and I wanted to push more.
whats the max i could push it to be safe:
any info thanks

 

[B16RacerN2NR]

1,000,000 PSI. Throw the stock injectors back on, turn down the fuel pressure, and watch it fly...

 

[awptickes]

I'd say about 15psi before you blow something. That's pretty normal for D-series.

jdm intercooler
afc tuning, stock ecu

RLY? What's a JDM intercooler look like? Is it different than a USDM intercooler? Oh, nevermind, I know. The JDM intercooler exits on the right side, right?

Lose the greddy e-manage. It's a good way to fuck up an engine.

 

[efhondakid]

Yeah I was wondering, whats the max boost i could push with my d16a6 motor?
specs:
stock internal
450cc injector
greddy td04 turbocharger with internal wastegate
jdm intercooler
afc tuning, stock ecu
so right now Im boosting 6 psi and I wanted to push more.
whats the max i could push it to be safe:
any info thanks

How about you just leave it at 6?

 

[t3t4delsol]

leave it where its at, get rid of the hack and get your ecu chiped and tuned properly, that piggy-back will end up blowing your motor. psi means nothing, you need to figure out how much cfm your turbo is putting out, a t-25 at 15psi will put out as much cfm as a t3/t4 60trim at 7psi, get it tuned properly if you want it to last

 

[newb]

1,000,000 PSI. Throw the stock injectors back on, turn down the fuel pressure, and watch it fly...

Lmfao!

To the OP, focus on your horsepower not your boost pressure.

 

[sammy_jimenez_1988]

im with del sol up there get it tunned that shit is hella important if u want a reliable car u can play with

 

[amadeuscr]

Yeah I was wondering, whats the max boost i could push with my d16a6 motor?
specs:
stock internal
450cc injector
greddy td04 turbocharger with internal wastegate
jdm intercooler
afc tuning, stock ecu
so right now Im boosting 6 psi and I wanted to push more.
whats the max i could push it to be safe:
any info thanks

with AFC , you are pushing killer->6psi , get your ECU Chipped first and tune it correctly !

 

[VTECBrag]

check out ZealAutowerks - Honda Compression Calculatorfind out what your effective CR is and make sure its a green signal. Too much boost will cause detonation, and thats not good for d stock internals. Unless you wanna spend loads of money rebuilding a car thats not meant for giving tonnes of horse power. The rod-stroke ratio isnt very boost friendly. If you just wanna boost with stock internals, expecting 160whp or something just go for 6 psi boost and tune it.
just my 2 cents

 

[763civicls21]

Yeah I was wondering, whats the max boost i could push with my d16a6 motor?
specs:
stock internal
450cc injector
greddy td04 turbocharger with internal wastegate
jdm intercooler
afc tuning, stock ecu
so right now Im boosting 6 psi and I wanted to push more.
whats the max i could push it to be safe:
any info thanks

unchipped ecu? interesting...probably should get it chip and get it tune....max psi is depending on the tune and motor condition...

 

[George777]

I doubt the OP even cares. He hasn't been on for almost a month now.