Vosty
"REP 4 U" Whore Member!!!
Hello Everyone... Im new to the forums. Thought I would post up my project...
Currently In The Worx...
.Swapping In My 2nd B18C1 "Fully Built For Bo0st"
♦Golden Eagle Sleeves (81.5mm bore)
♦Wiseco Coated Pistons (9.5:1)
♦Eagle H-Beam Rods.
♦ACL Bearings.
♦Whole Bottom End Plastigauged.
♦Golden Eagle Head Studs.
♦Skunk2 Intake Manifold.
♦MSD 6-AL Ignition.
♦Ebay Cold Air Intake "LOL"
♦AEM Fuel Dist.
♦3" Mandrel Exhaust By "Linder Power Systems"
♦3" Thermal R&D Muffler.
♦p28 Chipped ECU / VTEC @ 4800 rpm's - 8200 Redline
.SI Front & Rear Brake Conversion / SS Brake Lines
.ACT Chrome-Molly Flywheel
.Exedy Organic clutch
.Ingalls F&R Camber Kit "Should Have An Online Review on the Camber Install w/ Pix for you guys here soon."
Car Pix:::
http://apps.rockyou.com/rockyou.swf?instanceid=33003970
Engine Pix:::
http://apps.rockyou.com/rockyou.swf?instanceid=33009180
The Turbo Project will be done by Linder Power Systems, Not sure of everything that will be going into it just yet but it should get exciting:::
Check Out There Crazy Machining & Fabricating Work below:::
www.myspace.com/79208817
What color I should paint my car???
.Im considering these colors...
-Champ White
-IS300 Gray *Leaning towards this color*
-Stock
-Any recommendations and post pix of colorz if u like.
And I cant decide wether or not to paint the type r lip's and sides or leave it black...
Post Comments of wut u think
-Vosty
Currently In The Worx...
.Swapping In My 2nd B18C1 "Fully Built For Bo0st"
♦Golden Eagle Sleeves (81.5mm bore)
♦Wiseco Coated Pistons (9.5:1)
♦Eagle H-Beam Rods.
♦ACL Bearings.
♦Whole Bottom End Plastigauged.
♦Golden Eagle Head Studs.
♦Skunk2 Intake Manifold.
♦MSD 6-AL Ignition.
♦Ebay Cold Air Intake "LOL"
♦AEM Fuel Dist.
♦3" Mandrel Exhaust By "Linder Power Systems"
♦3" Thermal R&D Muffler.
♦p28 Chipped ECU / VTEC @ 4800 rpm's - 8200 Redline
.SI Front & Rear Brake Conversion / SS Brake Lines
.ACT Chrome-Molly Flywheel
.Exedy Organic clutch
.Ingalls F&R Camber Kit "Should Have An Online Review on the Camber Install w/ Pix for you guys here soon."
Car Pix:::
http://apps.rockyou.com/rockyou.swf?instanceid=33003970
Engine Pix:::
http://apps.rockyou.com/rockyou.swf?instanceid=33009180
The Turbo Project will be done by Linder Power Systems, Not sure of everything that will be going into it just yet but it should get exciting:::
Check Out There Crazy Machining & Fabricating Work below:::
www.myspace.com/79208817
What color I should paint my car???
.Im considering these colors...
-Champ White
-IS300 Gray *Leaning towards this color*
-Stock
-Any recommendations and post pix of colorz if u like.
And I cant decide wether or not to paint the type r lip's and sides or leave it black...
Post Comments of wut u think
-Vosty